Your cart

Total
CAD
Shipping and discount codes are added at checkout.

Spars, Rigging, and Hardware for Sailboats

Rig-Rite, Inc.
Phone: (001) 401-739-1140 -- FAX: (001) 401-739-1149
www.RigRite.com        Ordering/Questions

Wide Sheaves & Anchor Rollers

Sheaves are used to allow a line or wire to make a directional change of up to 180 degrees, without chafe and with a minimum of friction. Sheaves turn on Axles, and may have Bushings installed in them to reduce working friction, or to reduce their Inside Diameter (ID). Wide Sheaves are those where the Width is close to, or exceeds the Diameter (OD) of the Sheave. Primary usage of Wide Sheaves is found in Genoa Sheet Cars and in Anchor Rollers, with few Spar Applications.
Wide Sheaves and Anchor Rollers are listed here by Width, then Outside (Maximum) Diameter (OD), and Inside Diameter (Bore) in ascending order.

Rig-Rite stocks a variety of Wide Sheaves and most are listed below, but many other sizes have been produced over time. Please note that if a Sheave listed here meets your principal dimensions of Outside Diameter (OD) & Width, it is frequently possible to modify the Inside Diameter (ID) by either drilling it out to a larger size, or bushing it down to a smaller one. If a Sheave you require is not listed, please contact us specifying dimensions (OD, width, and ID), material (aluminum, plastic, etc.), and application. Standard (Narrow) Sheaves are listed separately, See Rig-Rite Sheaves.

 


 
1" Wide Sheaves
1 7/16" Wide Sheaves
1 5/8" Wide Sheaves
1 7/8" Wide Sheaves
 
2" Wide Sheaves
2 1/4" Wide Sheaves
2 1/2" Wide Sheaves
 
3" Wide Sheaves
3 1/2" Wide Sheaves
3 5/8" Wide Sheaves
4 1/4" Wide Sheaves

 


1" Wide Sheaves
1" Wide Delrin Sheave - 1" OD, 1/4" ID: PP S4D16-4:

Turned Black Delrin Sheave is 1" OD x 1" wide x 1/4" ID. As used on a variety of stanchion mount furling line blocks, and in other applications. With Rope Groove for up to 3/4" line.

 


1 7/16" Wide Sheaves
1 7/16" Wide Aluminum Sheave: Mer 7110-AS:

Black Anodized Aluminum Sheave is 1 5/8" OD x 1 7/16" wide x 1/2" ID. As used on Merriman Twin-sheet Genoa Lead Cars for 1" T-Track. Complete Replacement Sheave Assembly for those Cars is listed below.

 

Replacement Alu. Sheave Ass'y for Merriman 1" Car: Mer 7110-ASA:
Complete Replacement Sheave Assembly for Merriman Twin-sheet Genoa Lead Car for 1" T-Track. Assembly includes Black Anodized Aluminum Sheave, Mer 7110-AS, with special Delrin Bushing, spacing washers and a 1/4" bolt with locknut. Extremely low-friction arrangement is the permanent solution for replacement of original white plastic Sheave.

 


1 5/8" Wide Sheaves
1 5/8" Wide Delrin Sheave/ Anchor Roller: SAR6.5D13-6:
Black Delrin sheave is 1 3/4" OD x 1 5/8" (1.585") wide x 3/8" ID. Wide turned sheave has shallow groove for use with a variety of anchor rollers.

 

1 5/8" Wide Rubber Sheave/ Anchor Roller: SAR6.5R13-B8:

Black Rubber sheave is 2 1/2" OD x 1 5/8" (1.585") wide x 1/2" ID. Wide neoprene sheave has deep groove and integral brass bushing for use with a variety of anchor rollers.

 


1 7/8" Wide Sheaves
1 7/8" Wide Delrin Sheave: Mer 7120-DS:
Black Delrin Sheave is 2 3/8" OD x 1 7/8" wide x 7/8" ID. As used on Merriman Twin-sheet Genoa Lead Cars for 1", 1 1/4" and 1 1/2" T-Track. Complete Replacement Sheave Assembly for those Cars is listed below.

 

Replacement Delrin Sheave Ass'y for large Merriman Genoa Car: Mer 7120-DSA:
Replacement Sheave Assembly for large Merriman Twin-sheet Genoa Lead Car. Assembly includes Black Delrin Sheave, Mer 7120-DS, with special Delrin Bushing (3/8" ID) and spacing washers. Extremely low-friction arrangement is the solution for replacement of original Aluminum Sheave.

 

1 7/8" Wide Aluminum Sheave/ Anchor Roller: SAR-CC1:

Anodized Aluminum sheave is 2 5/8" OD x 1 7/8" wide x 7/16" ID. Wide turned sheave has shallow groove. As used on a variety of C&C Yachts Anchor Rollers.

 

1 7/8" Wide Aluminum Sheave/ Anchor Roller: SAR-CC1-C:

Anodized Aluminum sheave is 2 5/8" OD x 1 7/8" wide x 1/2" ID. Special Wide sheave has double groove for use with Rope and Chain up to 1/2". As used on a variety of C&C Yachts Anchor Rollers.

 

1 7/8" Wide Delrin Sheave: SK-SW11D30-20mm:

Grey molded plastic Sheave is 2 3/4" (70mm) OD x 1 7/8" wide (47mm) x 20mm (>3/4" ID). As used on Lewmar Twin-sheet Genoa Lead Cars for 1 1/4" and 32mm T-Track.

 


2" Wide Sheaves
2" Wide Aluminum Sheave: SK-SW9A32-B10:

Anodized Aluminum sheave is 2 1/4" OD x 2" wide x 5/8" ID. Wide Black sheave features special Nomex-Teflon Bushings to minimize friction. As used on Schaefer Twin-sheet Genoa Lead Cars, and in other applications.

 


2 1/4" Wide Sheaves
2 1/4" Wide Nylon Sheave/ Anchor Roller: SAR9.2N36-8:
Wide Nylon sheave is 2 3/8" OD x 2 1/4" wide x 1/2" ID. Wide molded sheave has shallow groove for use with a variety of anchor rollers.

 

2 1/4" Wide Bronze Sheave/ Anchor Roller: SAR9.2B36-8:

Wide Bronze sheave is 2 3/8" OD x 2 1/4" wide x 1/2" ID. Wide Cast Bronze sheave has shallow groove for use with a variety of anchor rollers.

 


2 1/2" Wide Sheaves
2  1/2" Wide Aluminum Sheave/ Anchor Roller: SAR-CC2:
Anodized Aluminum sheave is 2 7/8" OD x 2 1/2" (2.44") wide x 11/16" ID. Wide turned sheave has shallow groove. As used on a variety of C&C Yachts Anchor Rollers. w/hub

 

2  1/2" Wide Aluminum Sheave/ Anchor Roller: SAR-CC2-C:
Anodized Aluminum sheave is 2 7/8" OD x 2 1/2" (2.44") wide x 11/16" ID. Special Wide sheave has double groove for use with Rope and Chain up to 3/8". As used on a variety of C&C Yachts Anchor Rollers.

 

2  1/2" Wide Delrin Sheave/ Anchor Roller, 1/2" ID: SAR8D40-8OD:

Wide Delrin sheave is 2" OD x 2 1/2" wide x 1/2" ID. Wide white turned sheave has shallow groove for use with a variety of anchor rollers. As used on O'Day 302 & 322 Anchor Rollers, and in other applications. WS11593

 


3" Wide Sheaves
3" Wide Rubber Sheave/ Anchor Roller: SAR11R48-B10:

Black Rubber sheave is 2 3/4" OD x 3" (2.94") wide x 5/8" ID. Wide neoprene sheave has shallow groove with Chain notch and integral brass bushing for use with a variety of anchor rollers.

 

3" Wide Nylon Sheave/ Anchor Roller: SAR12N48-10:
Wide Nylon sheave is 3" OD x 3" (2.94") wide x 5/8" ID. Wide molded sheave has shallow groove for use with a variety of anchor rollers.

 

3" Wide Bronze Sheave/ Anchor Roller: SAR12B48-10:
Wide Bronze sheave is 3" OD x 3" (2.94") wide x 5/8" ID. Wide Cast Bronze sheave has shallow groove for use with a variety of anchor rollers.

 


3 1/2" Wide Sheaves
3  1/2" Wide Aluminum Sheave/ Anchor Roller: SAR-CC3:
Anodized Aluminum sheave is 4" OD x 3 1/2" (3.375") wide x 11/16" ID. Wide turned sheave has shallow groove. As used on a variety of C&C Yachts Anchor Rollers. w/hub

 

3  1/2" Wide Aluminum Sheave/ Anchor Roller: SAR-CC3-C:
Anodized Aluminum sheave is 4" OD x 3 1/2" (3.375") wide x 11/16" ID. Special Wide sheave has double groove for use with Rope and Chain up to 3/8". As used on a variety of C&C Yachts Anchor Rollers. w/hub

 

3  1/2" Wide Rubber Sheave/ Anchor Roller: SAR12R56-B10:

Black Rubber sheave is 3" OD x 3 1/2" (3.44") wide x 5/8" ID. Wide neoprene sheave has shallow groove with Chain notch and integral brass bushing for use with a variety of anchor rollers.

 

3  1/2" Wide Delrin Sheave/ Anchor Roller: SARM90D80-14mm:

White Delrin sheave is 80mm (3 1/8") OD x 90mm (3 1/2") wide x 14mm (9/16") ID. Wide Delrin sheave has shallow groove. As used on auxiliary anchor rollers on Sparcraft T44 and T55 Crossbeams.

 


3 5/8" Wide Sheaves
3 5/8" Wide Nylon Sheave/ Anchor Roller: SAR16N50-12:
Wide Nylon sheave is 4" OD x 3 5/8" wide x 3/4" ID. Wide molded sheave has shallow groove for use with a variety of anchor rollers.

 

3 5/8" Wide Bronze Sheave/ Anchor Roller: SAR16B50-12:
Wide Bronze sheave is 4" OD x 3 5/8" wide x 3/4" ID. Wide Cast Bronze sheave has shallow groove for use with a variety of anchor rollers.

 


4 1/4" Wide Sheaves
4 1/4" Wide Nylon Sheave/ Anchor Roller: SAR19N68-12:
Wide Nylon sheave is 4 3/4" OD x 4 1/4" wide x 3/4" ID. Wide molded sheave has shallow groove for use with a variety of anchor rollers.

 

4 1/4" Wide Bronze Sheave/ Anchor Roller: SAR19B68-12
Wide Bronze sheave is 4 3/4" OD x 4 1/4" wide x 3/4" ID. Wide Cast Bronze sheave has shallow groove for use with a variety of anchor rollers.

~ Top ~

~ Back to Rig-Rite Home Page ~