 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Z341 Spreaders and Components |
|
|
|
|
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Z341 Spreaders and Components |
|
|
|
|
|
Z-Spar Z341 Spreader Section Outside Measurements (Untapered): 155mm x 49mm (6 1/8" x 1 15/16") Inside Measurements: 41mm wide (1 5/8") Wall thickness: 4mm Alloy: 6005A Weight/M.: 3.6kg. - Weight/ft.: 2.42 lbs. |
|
|
The Z341 Spreader Section features an integral "tail", so that the Spreaders (as an option)
can be tapered at the outboard end without welding. Z341 Spreader Assemblies are available in Standard
(untapered), and Tapered versions with a variety of inboard and outboard end fittings, listed below.
As used on Leopard 50, Hanse 575, Dufour 560, Neel 65, Prout 50, Oceanis 500, and others. |
|
|
|
|
|
Z341 Spreader Section, Clear Anodized: Z-341CA-____: Z341 Spreader Section, Clear Anodized x 3' 3": Z-341CAx1M: Z341 Spreader Section, Clear Anodized x 4' 11": Z-341CAx1.5M: Z341 Spreader Section, Clear Anodized x 6' 6": Z-341CAx2M: Z341 Spreader Section is available clear anodized without taper or drilling at lengths up to 7.2M (23' 7"). To order: specify length.
|
|
|
Z341 Untapered Spreader - Tube only, Angled Aft: Z-341T-____: Z341 Tapered Spreader - Tube only: Z-341TT-__: Z341 Tapered Spreader Tube only - Angled Aft: Z-341TTAA-____: For replacement purposes when using original end fittings, Z341 Spreader Tubes are available Tapered or Untapered and with inboard angles cut. To order: specify maximum tube length, and sweepback angle (if any). Clear anodized finish is standard. Painted finishes are available on special order, specify color.
|
|
|
Z341 Spreader Assemblies To order Z341 Spreader Assemblies, specify Tube and Tip Part numbers, maximum tube length and sweepback angle (if any).
|
|
|
|
|
| Spreader Tips & Components for Z341 Spreaders | |||
| Continuous Spreader Tips | |||
| Continuous Spreader Tip for Z341 Tapered Spreader - Triple Shroud: Z-3026A: | |||
|
Cast aluminum Spreader Tip for use with Tapered Z341 Spreader incorporates provisions
for up to 3 shrouds (the largest up to 16mm (5/8")). Shrouds are captured by smooth outer casting
that is attached to the base casting with two screws. Recessed Allen head cap screws (8mm) thread
into captive locknuts in base casting.
|
|
||
| Continuous Spreader Tip for Z341 Standard Spreader - Triple Shroud: Z-3025A: | |||
|
Cast aluminum Spreader Tip for use with Standard Z341 Spreader incorporates provisions
for up to 3 shrouds (the largest up to 16mm (5/8")). Shrouds are captured by smooth outer casting
that is attached to the base casting with two screws. Recessed Allen head cap screws (8mm) thread
into captive locknuts in base casting.
|
|
||
|
|
|||
| Discontinuous Tips | |||
|
Discontinuous Spreader Tip Ass'y for Z341 - 16/12mm: Z-4026-1612A:
Discontinuous Spreader Tip Ass'y for Z341 - 19/12mm: Z-4026-1912A: Discontinuous Spreader Tip for Z341 - 19/12mm, Casting only: Z-4026-1912CO: Discontinuous Spreader Tip Ass'y for Z341 - 19/16mm: Z-4026-1916A: Discontinuous Spreader Tip Ass'y for Z341 - 22/16mm: Z-4026-2216A: |
|||
|
Cast aluminum Spreader Tip for use with Tapered Z341 Spreader incorporates a 16mm, 19mm
or 22mm Pin outboard for the main shrouds, and a 12 or 16mm inboard Pin for intermediate shrouds.
Design allows for Discontinuous or Continuous Diagonal shrouds. Unit projects (maximum) 3 15/16"
(100mm) from end of spreader tube. Slot width (at outboard pin) is 1 5/8" (40mm), pin center is 2 1/2"
(62mm) from tube end. Inboard Pin has slot width of 1/2" (12mm), small pin center is 1" (25mm)
from tube end. Pins are included (except on the casting only, Z-4026-1912CO).
|
|
||
|
12mm pin for Z-1155 Tip Casting: Z-4026P-12: 16mm pin for Z-1155 Tip Casting: Z-4026P-16: 16mm Outboard pin for Z-1155 Tip Casting: Z-4026P-16L: 19mm pin for Z-1155 Tip Casting: Z-4026P-19: 22mm pin for Z-1155 Tip Casting: Z-4026P-22: SS Pins only for rigging attachment on Z-4026 Discontinuous Spreader Tips, above. Inboard Pins are 72mm (2 7/8") long, Outboard Pins are 87mm (3 7/16") long.
|
|
||
|
Discontinuous Spreader Tip for Z341 'Tapered' B&R Rig 16mm/12mm: Z-4054-1612A: Discontinuous Spreader Tip for Z341 'Tapered' B&R Rig 19mm/16mm: Z-4054-1916A: Discontinuous Spreader Tip for Z341 'Tapered' B&R Rig 19mm/16mm: Z-3043-1916BR: |
|||
|
Cast aluminum Spreader Tip for use with Tapered Z341 Spreader on B&R Rigs incorporates
a 16mm or 19mm Pin outboard for the main shrouds, and a 12mm or 16mm inboard Pin for intermediate shrouds.
Design allows for Discontinuous or Continuous Diagonal shrouds. Unit projects (maximum) 3 15/16"
(100mm) from end of spreader tube. Slot width (at outboard pin) is 1 5/8" (40mm), pin center is
2 1/2" (62mm) from tube end. Inboard Pin has slot width of 1/2" (12mm), small pin center is 1"
(25mm) from tube end. Pins (included) are as Z-1155P, above.
|
|
||
|
|
|||
| Spreader Bars for Z341 Spreaders | |||
|
Aluminum Spreader Bars for Z341 Spreaders Extruded Aluminum Spreader Bars for Z341 Spreaders feature a slot for a SS Fixing Plate to secure the Spreaders in place. Bar section (Z455) is 60mm x 40mm (2 3/8" x 1 9/16"), alloy 6060, and slides inside the Z341 Spreader Section.
|
|||
|
Aluminum Spreader Bar for Z341 - 0° aft, 5° lift: Z-5210-0: Aluminum Spreader Bar for Z341 - 0° aft, 0° lift: Z-5210-00: Aluminum Spreader Bar for Z341 - 20° aft, 5° lift: Z-5210-20: Aluminum Spreader Bar for Z341 - 20° aft, 0° lift: Z-5210-200: Aluminum Spreader Bar for Z341 - 25° aft, 5° lift: Z-5210-25: |
|||
|
Extruded Aluminum Spreader Bar for Z341 Spreaders is available in a variety of angles with Standard
(5-6°) lift, and with no lift (for B&R Rigs).
|
|
||
|
|
|||
|
Doubler Plate for Z341 Spreader Bar, 0-15°: Z-4117:
Doubler Plate for Z341 Spreader Bar, 20°+: Z-4117L: Aluminum Reinforcing Plate fits the mast section and features boss to allow a straight cut on the spreader end. Cast Aluminum Plate is 7 1/4" long x 3 1/4" (maximum) wide (185 x 84mm), slot in plate is 1 1/4" high x 2 1/16" long (32 x 52mm). Plates (1 on each side) are attached to the mast with (6) 1/4" (6mm) rivets. For use with Z1001 and larger Mast sections. |
|
||
|
|
|||
|
Doubler Plate for Z341 Spreader Bar, 0-20°, newer style: Z-5757: Newer style Cast Aluminum Doubler Plate for Z341 Spreader Bars. The earlier style Doubler Plates, above, remain available.
|
|||
~ Back to Z-Spar Spreader Page ~
~ Home ~