 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Z-Spar Winch Pads |
|
|
|
|
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Z-Spar Winch Pads |
|
|
|
|
| Z-Spar uses a variety of cast or formed aluminum Winch Pads (Winch
Brackets) the most common of which are listed here. If you require a Winch Pad not
listed below please specify Mast Section, and Winch Pad dimensions when inquiring. |
|
|
|
| Standard Winch
Pads |
|
| Side Winch Pad: Z-1086:
Cast aluminum Winch Bracket mounts to the side of Z145, Z170, Z190, Z230 & Z230E Furling Mast Sections. Winch mounting surface on Bracket is 3 1/2" (90mm) square. Bracket is 3 1/2" (90mm) wide x (maximum) 5 1/16" (130mm) high. Grey anodized Bracket is offset and fastens to Mast with four (4) 5mm (3/16") screws or rivets.
|
|
| Side Winch Pad: Z-1077:
Cast aluminum Winch Bracket mounts to the side of Z265, Z301, Z351, Z401, Z501, Z531 & Z300E, Z400E, and Z500E Furling Mast Sections. Winch mounting surface on Bracket is 5" (120mm) square. Bracket is 5" (120mm) wide x (maximum) 8" (200mm) high. Grey anodized Bracket is offset and fastens to Mast with eight (8) 6mm (1/4") screws or rivets.
|
|
| Side Winch Pad: Z-1088:
Cast aluminum Winch Bracket mounts to the side of Z601, Z701, Z901 & Z600E, Z700E, Z800E, and Z900E Furling Mast Sections. Winch mounting surface on Bracket is 5 3/4" (145mm) square. Bracket is 5 3/4" (145mm) wide x (maximum) 10" (250mm) high. Grey anodized Bracket is offset and fastens to Mast with eight (8) 6mm (1/4") screws or rivets.
|
|
| Side Winch Pad: Z-151:
Formed aluminum Winch Bracket mounts to the side of Z901, Z1101, Z1400 & Z900E, Z1100E, and Z1400E Furling Mast Sections. Winch mounting surface on Bracket is 7 5/8" (195mm) square. Bracket is 7 5/8" (195mm) high x (maximum) 10 1/4" (260mm) wide. Clear anodized Bracket is 6mm (1/4") thick and fastens to Mast with twelve (12) 6mm (1/4") screws or rivets.
|
|
|
|
|
| Aft-Mount
Winch Pads for Reef Lines Aft-mount Winch Pads are made so that the bottom of the mounted winch will be angled at approximately 13° aft of the mast. This helps to align the winch for better use with Reefing Lines exiting from the forward end of the boom. |
|
| Aft Winch Pad: Z-1082:
Cast aluminum Winch Bracket mounts to the aft side of Z265, Z301, Z351, Z401, Z-501, Z531 and other Mast Sections. Winch mounting surface on Bracket is 3 7/8" (100mm) square. Bracket is 3 7/8" (100mm) wide x (maximum) 6 13/16" (175mm) high. Grey anodized Bracket fastens to Mast with eight (8) 6mm (1/4") screws or rivets.
|
|
| Aft Winch Pad: Z-1087:
Cast aluminum Winch Bracket mounts to the aft side of Z601, Z701 and other Mast Sections. Winch mounting surface on Bracket is 4 7/8" (124mm) square. Bracket is 4 7/8" (124mm) wide x (maximum) 8 1/8" (206mm) high. Grey anodized Bracket fastens to Mast with eight (8) 6mm (1/4") screws or rivets.
|
|
| Aft Winch Pad: Z-152:
Aluminum Winch Bracket mounts to the aft side of Z901, Z1101 and other Mast Sections. Winch mounting surface on Bracket is 6 5/16" (160mm) wide x 7 1/2" (190mm) high. Bracket is 6 5/16" (160mm) wide x (maximum) 8" (203mm) high. Clear anodized, formed plate Bracket fastens to Mast with four (4) 6mm (1/4"), and two (2) 8mm (5/16") screws.
|
|
~ Home ~