|
Cast aluminum gooseneck assembly incorporates provisions for internal outhaul and 2 internal reef lines.
Outhaul line exits through aluminum sheave on centerline and runs along boom bottom to a cleat.
Reef lines exit port and starboard running past lever action cams, over delrin sheaves, and down.
SS cover plates keep lines on sheaves at all times.
Includes SS combination Toggle/Tack/Reef Hook Assembly, K-10345A.
Toggle attaches to any Kenyon gooseneck bracket designed for 1 1/2" toggle and
3/8" vertical pin. Vertical pin, CP6-76K, is not included.
Distance from vertical Toggle Pin to boom tube is 5 1/2". |
|
3656 Internal Gooseneck Assembly: K-43002-36:
As K-43002-36A, above, but without SS combination Toggle/Tack/Reef Hook
Assembly, K-10345A.
Distance from horizontal Pin hole to boom tube is 4 1/2". |
 |
3656 Internal Gooseneck Ass'embl'y w/o Cams: K-43002-36NC:
As K-43002-36, above, but with SS spacers in place of the reef cams.
For use where reef lines are led down to the deck and cleated aft on the cabin top. |
 |
|
|
Parts for 3656 Internal Gooseneck Assemblies |
Gooseneck Toggle/Tack w/ Reef Hooks: K-10345A:
Used with a variety of Kenyon goosenecks, this combination Toggle/Tack/Reef Hook
Assembly features 3 tack positions and includes 3/8" tack fastpin, K-10557.
Takes 3/8" vertical and horizontal pins.
Two reef hooks allow for ease of reefing from either side of the boom.
Toggle portion is 1 1/2" high x 7/8" wide with 1" between pin centers. Unit (excluding Reef Hooks)
is 4" high x 7/8" wide x 2 1/4" long. Attaches directly to any of the Kenyon SS Gooseneck Brackets
designed for a 1 1/2" Toggle with 3/8" vertical pin, CP6-76K.
|
 |
3656 Internal Gooseneck Casting Only: K-10340M-36:
Replacement casting only for any of the Kenyon internal gooseneck assemblies listed above.
|
 |
Outhaul Sheave for 3656 Gooseneck: K-198-7A:
Anodized aluminum sheave is 1 3/4" OD x 31/64" wide x 3/8" ID. |
|
Outhaul Sheave Axle for 3656 Gooseneck: K-10380:
SS axle pin is 3/8" diameter x 1" grip, with a turned groove on each end to accept 3/8" SS Snap
Rings, K-63015 (2 included). |
|
SS Snap Rings for 3/8"Axle Pin: K-63015-2P:
In 2-pack. Require small snap ring pliers for attachment. |
 |
Double Reef Cam Conversion Kit for 3656: K-11443:
Cam Conversion Kit for 3656 Gooseneck contains all Reef Line components included in the
K-43002-36 Assemblies, above.
Kit includes Cam levers, adjustable friction washers, reef Sheaves, SS spacers, Cover plates,
bolts and locknuts. Individual components are listed separately, below. |
|
|
Reefing Sheave for 3656 Gooseneck: K-11412:
Delrin sheave is 1" OD x 1/2" wide x 1/2" ID.
|
|
| |
Reefing Sheave Spacer for 3656 Gooseneck: K-11413:
SS spacer is 1/2" OD x 3/8" ID x .525" long. Used with Sheaves, and in place of Cams when reef lines
are not cleated at the gooseneck. |
|
| |
SS Cover Plate for 3656 Gooseneck - Port: K-11411P:
SS Cover Plate for 3656 Gooseneck - Star.: K-11411S:
Formed SS cover plate has 3/8" holes for sheave and cam bolts. Specify Port or Starboard.
|
|
| |
Gooseneck Reef Cam - Port: K-11246P:
Gooseneck Reef Cam - Starboard: K-11246S:
New-Style Cast aluminum Cam lever fits on 3/8" bolt and has recesses for special
friction-lock washers, K-10862 (2 included). Specify Port or Starboard. |
|
|
Friction-lock washers for Reef Cams: K-10862:
Special green-colored friction-lock washers made of an impregnated synthetic allow for
precise adjustment of cam tension and protect cams from corrosion.
|
|
