Spars, Rigging, and Hardware for Sailboats

Rig-Rite, Inc.
Phone: (001) 401-739-1140 -- FAX: (001) 401-739-1149
www.RigRite.com          Ordering/Questions

Z-Spar Hinged Mast Steps


Z-Spar has produced an incredible variety of cast aluminum Standard and Tabernacle (hinged) Mast Steps. Most Hinged (Tabernacle) Mast Steps are listed below, for Standard (non-hinging) Mast Steps, See, Z-Spar Standard Mast Steps. If you require a Hinged Mast Step not listed below, please specify Mast Section and Mast Step description when inquiring.
New-Style Hinged Tabernacle Deck Plates & Mast Feet
Old-Style Hinged Tabernacle Deck Plates & Mast Feet
Standard (non-Hinged) Mast Steps

New-Style Tabernacle Deck Plates and Mast Feet
Deck Plate for Tabernacle Mast Step w/ 1/4" Pin: Z-1100A:
Cast aluminum Deck Plate for use with Tabernacle Mast Foot on Z145, Z170, and Z190 Mast Sections. Features holes on each side for use with Z-261, Z-272 and Z-300 turning blocks, or Z-300SA Block Studs. Mast Foot hinges on 6mm pin (Z-1719), included, which goes through holes on aft side of Deck Plate. Deck Plate measures 4 7/8" (124mm) long, by 4 1/4" (108mm) wide and fastens to deck with (4) 1/4" (6mm) FH screws.

 

Z-1100

 

 

Tabernacle Hinge Pin – 6mm (1/4"): Z-1719:
SS Hinge Pin for use with Z-1100 Deck Plate is 6mm (1/4") diameter.

 

Z-1719

Tabernacle Mast Foot for Z145: Z-1397:
Cast aluminum Mast Foot for Z145 section hinges on 6mm pin (Z-1719) which goes through holes on aft side of Z-1100 Deck Plate. Unit may be labeled 1397.

 

Tabernacle Mast Foot for Z170: Z-1095:
Cast aluminum Mast Foot for Z170 section hinges on 6mm (1/4") pin (Z-1719) which goes through holes on aft side of Z-1100 Deck Plate. Unit may be labeled 1011 and/or 1095.

 

Z-1095

Tabernacle Mast Foot for Z190 - Small: Z-1096:
Small Cast aluminum Mast Foot for Z190 section hinges on 6mm (1/4") pin (Z-1719) which goes through holes on aft side of Z-1100 Deck Plate. Unit is (maximum) 5" (127mm) long x 3 1/4" (82mm) wide. Unit may be labeled 1012 and/or 1096.

 


Deck Plate for Tabernacle Mast Step w/ 5/16" Pin: Z-1101A:
Cast aluminum Deck Plate for use with Tabernacle Mast Foot on Z190, Z230 and Z265 Mast Sections. Features holes on each side for use with Z-261, Z-272 and Z-300 turning blocks, or Z-300SA Block Studs. Mast Foot hinges on 8mm (5/16") pin (Z-1316), included, which goes through holes on aft side of Deck Plate. Deck Plate measures 6" (152mm) long, by 5 1/8" (130mm) wide and fastens to deck with (4) 1/4" (6mm) FH screws.

 

Z-1101
 

 

Tabernacle Hinge Pin – 8mm (5/16"): Z-1316:
SS Hinge Pin for use with Z-1101 Deck Plate is 8mm (5/16") diameter.

 

Z-1316

Tabernacle Mast Foot for Z190 - Large: Z-1171:
Large cast aluminum Mast Foot for Z190 section hinges on 8mm (5/16") pin (Z-1316) which goes through holes on aft side of Z-1101 Deck Plate. Unit is (maximum) 5 1/4" (134mm) long x 3 1/4" (82mm) wide. Unit may be labeled 1012 and/or 1171.

 

Tabernacle Mast Foot for Z230: Z-1097:
Cast aluminum Mast Foot for Z230 section hinges on 8mm (5/16") pin (Z-1316) which goes through holes on aft side of Z-1101 Deck Plate. Unit may be labeled 1014 and/or 1097.

 

Tabernacle Mast Foot for Z230E: Z-4001:
Cast aluminum Mast Foot for Z230E furling mast section hinges on 8mm (5/16") pin (Z-1316) which goes through holes on aft side of Z-1101 Deck Plate. Unit may be labeled 4001.

 

Z-4001
Tabernacle Mast Foot for Z265: Z-1098:
Cast aluminum Mast Foot for Z265 section hinges on 8mm (5/16") pin (Z-1316) which goes through holes on aft side of Z-1101 Deck Plate. Unit may be labeled 1015 and/or 1098.

 


Old-Style Tabernacle Deck Plates and Mast Feet w/ Sheaves
Old-Style Mast Feet with integral sheaves have been obsoleted. Some sizes and angles are available on a limited basis.

 

Old-Style Deck Plate for Z145 - Z190 Mast Foot w/ Sheaves: Z-1112:
Aluminum Deck Plate fits Z145, Z170, and Z190 Mast Feet with Sheaves. Cast Plate measures 97mm (3 13/16") long (on deck) x 60mm (2 5/16") wide, with vertical rib, and slot on aft side for 6mm pin. Attaches to deck with (4) 6mm (1/4") FH screws on 32mm (1 1/4") x 79mm (3 1/8") centers.

 

Z-1112
Mast Foot w/ Sheaves for Z145: Z-145SF-20: Z-145SF-10/245
Mast Foot w/ Sheaves for Z145: Z-145SF-30:
Mast Foot w/ Sheaves for Z145: Z-145SF-210:
Mast Foot w/ Sheaves for Z145: Z-145SF-10/245:
Mast Foot w/ Sheaves for Z145: Z-145SF-10/290:
Old-Style small Cast Aluminum Mast Foot with Sheaves for Z145 Mast and Z-1112 Deck Plate. Used with up to six (6) 28mm Sheaves, Z-1614, and 6mm knurled axle Pins in a variety of lengths. These Mast Feet are no longer available, See: Mast Foot Replacement Kit for Z145.

 

Mast Foot w/ Sheaves for Z170: Z-170SF-30:
Old-Style small Cast Aluminum Mast Foot with Sheaves for Z170 Mast and Z-1112 Deck Plate. Used with up to six (6) 28mm Sheaves, Z-1614, and 6mm knurled axle Pins in a variety of lengths. This Mast Foot is no longer available, See: Mast Foot Replacement Kit for Z170.

 

Mast Foot w/ Sheaves for Z190: Z-190SF-30:
Mast Foot w/ Sheaves for Z190: Z-190SF-210:
Mast Foot w/ Sheaves for Z190: Z-190SF-10/245:
Mast Foot w/ Sheaves for Z190: Z-190SF-10/260:
Old-Style small Cast Aluminum Mast Foot with Sheaves for Z190 Mast and Z-1112 Deck Plate. Used with up to six (6) 28mm Sheaves, Z-1614, and 6mm knurled axle Pins in a variety of lengths. These Mast Feet are no longer available, See: Mast Foot Replacement Kit for Z190.

 

Mast Foot Replacement Kit for Z145: Z-145SF-SKit:
Mast Foot Replacement Kit for Z170: Z-170SF-SKit:
Mast Foot Replacement Kit for Z190: Z-190SF-SKit:
Replacement Kit for Old-Style small Mast Feet includes Z-1100A Deck Plate, above, with special high-density Spacer, and the proper size Mast Foot and rivets to go with it. This arrangement eliminates the need to shorten rigging required with the New-Style Tabernacle alone, while maintaining Boom height. Conversion requires a separate Exit Plate, Z-3273, for halyards cleated on the Mast. For each halyard that was led through the Old-Style Mast Foot to the deck, an Exit Plate, Z-3273, and a Turning Block, Z-261, Z-272, or Z-300, or Z-300SA Block Stud will be required (order separately). Attaches to deck with (4) 6mm (1/4") FH screws using original hole spacing. To order, specify Mast Section.

 

 

Old-Style Deck Plate for Z230, Z260 Mast Foot w/ Sheaves: Z-1112L:
Aluminum Deck Plate fits Z230 and Z260 Mast Feet with Sheaves. Cast Plate measures 138mm (5 7/16") long x 78mm (3 1/16") wide, with vertical rib and horizontal SS 8mm pin. Attaches to deck with (4) 6mm (1/4") FH screws.

 

Z-1112L
Mast Foot w/ Sheaves for Z230: Z-230SF-10/270:
Old-Style large Cast Aluminum Mast Foot with Sheaves for Z230 Mast and Z-1112L Deck Plate. Used with up to six (6) 45mm Sheaves, Z-1616, and 8mm knurled axle Pins in a variety of lengths. This Mast Foot is no longer available, See: Mast Foot Replacement Kit for Z230.

 

Mast Foot Replacement Kit for Z230: Z-230SF-SKit:
Replacement Kit for Old-Style Z230 Mast Feet includes Z-1101A Deck Plate, above, with special high-density Spacer, and the Mast Foot, Z-1097, and rivets to go with it. This arrangement eliminates the need to shorten rigging required with the New-Style Tabernacle alone, while maintaining Boom height. Conversion requires a separate Exit Plate, Z-3273, or Z-3272, for halyards cleated on the Mast. For each halyard that was led through the Old-Style Mast Foot to the deck, an Exit Plate and a Turning Block, Z-261, Z-272, or Z-300, or Z-300SA Block Stud will be required (order separately). Attaches to deck with (4) 6mm (1/4") FH screws, New Deck holes will have to be drilled.

 

 
Mast Foot w/ Sheaves for Z260: Z-260SF-30:
Mast Foot w/ Sheaves for Z260: Z-260SF-10/230:
Mast Foot w/ Sheaves for Z260: Z-260SF-10/260:
Cast Aluminum Mast Foot with Sheaves for Z260 Mast and Z-1112L Deck Plate. Used with up to six (6) 45mm Sheaves, Z-1616, and 8mm knurled axle Pins in a variety of lengths. These Mast Feet are no longer available.

 

Z-260SF-10/230

Old-Style Deck Plate for Z260 Mast Foot w/ Sheaves: Z-1175X:
Aluminum Deck Plate to fit old-style Z260 and other Mast Feet with Sheaves. Cast Plate measures 160mm (6 5/16") long x 120mm (4 3/4") wide x 22mm (7/8") thick, with fore and aft slot to accept rib in mast foot, and slot in aft side for 6mm hinge pin. Attaches to deck with up to (8) 6mm (1/4") FH screws. As used on early O'Day 272, and others. *

 

Z-1175
Mast Foot w/ Sheaves for Z260: Z-260SF-10/2P:
Cast Aluminum Mast Foot with Sheaves for Z260 Mast and Z-1175X Deck Plate. Used with up to six (6) 45mm Sheaves, Z-1616, and 8mm knurled axle Pins in a variety of lengths. As used on early O'Day 272, and others. *

 

~ Back to Z-Spar Mast Page ~

~ Back to Z-Spar Main Page ~

~ Back to Rig-Rite Home Page ~