 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Z-Spar Batten Cars |
|
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Z-Spar Batten Cars |
|
| Z-Spar uses its own Recirculating Ball Batten Cars and special Full Batten
Mast Track. Clear anodized Recirculating Ball Track is 24.7mm (>1"), or 30mm (1 3/16") wide.
To order Batten Cars and Parts not listed below, we will require a
sketch or photo of the parts with complete dimensions. |
|
Z-Spar Batten Track for Mast: Z-____-__: Z-Spar uses a variety of Full Batten Mast Tracks. Tracks of a given width differ only by the means with which they attach to the Mast. Clear anodized Recirculating Ball Tracks are 24.7mm (<1"), or 30mm (1 3/16") wide. To order Track to fit a Z-Spar Mast, you must specify which Mast Section it is to fit, See: Z-Spar Mast Specifications and Components.
|
||
|
End Stop w/ Bumper for Z-Spar Batten Track: Z-1138A: End Cap for use with Z-Spar Full Batten Mast Tracks incorporates a rubber bumper, Z-150, to reduce impact stress. Cast aluminum End Cap is 24mm (1 15/16") long x 35mm (1 3/8") wide, and attaches to Track with (1) 6mm (1/4") screw.
|
||
|
Short Batten Car for Z-Spar RCB Track: Z-3481AT: Batten Car designed for use with Masts using Z-Spar Full Batten Mast Track that is 24.7mm (<1") wide. Car incorporates fully articulating toggle with 10mm threaded stud (22mm long) for batten attachment. Car rides on Torlon Ball Bearings to provide high strength and low friction at a minimum weight. Extruded Aluminum Car has removable end caps, for easy ball replacement. Car is 82mm (3 1/4") long x 60mm (2 3/8") wide. Short Batten Car uses forty-four (44) Torlon ball bearings.
|
 |
|
|
|
End Cap for Z-Spar 60mm wide Batten Cars: Z-EC25-1: Replacement End Cap for Z-Spar Batten Cars for Track that is 24.7mm (<1") wide. End Cap is 60mm (2 3/8") wide x (maximum) 40mm (1 9/16") high x 13mm (1/2") thick, and has 5mm (3/16") hole for attachment to Car. 3481
|
 |
|
|
Ball Bearing Set for Z-3481 & Z-3485 Batten Cars: Z-BP6M-T44: Replacement ball bearing pack for Z-3481AT and Z-3485AT Batten Car contains forty-four (44) 6.4 mm Torlon ball bearings.
|
|
|
|
Cast Toggle for Z-3481 & Z-3485 Batten Cars: Z-3481-TCA: Cast Aluminum Toggle as used on Z-3481AT and Z-3485AT Batten Cars. Cast Toggle is 26mm high x 18mm wide x (maximum) 36mm long with holes for 8mm vertical pin and includes 6mm screw and locknut set, Z-3481-6S.
|
|
|
|
SS Toggle for Z-3481 & Z-3485 Batten Cars: Z-3481-TSA: Welded Stainless Steel Toggle as used on Z-3481AT and Z-3485AT Batten Cars. SS Toggle is 26mm high x 12mm wide x (maximum) 36mm long with holes for 8mm vertical pin and 6mm horizontal screw.
|
|
|
|
SS Stud for Z-3481 & Z-3485 Batten Cars: Z-3481-S10: Stainless Steel Stud as used on Z-3481AT and Z-3485AT Batten Cars. Threaded Stud has 10mm thread x 20mm long, x (maximum) 50mm long with 6mm cross hole.
|
|
|
Short Batten Car for Z-Spar RCB Track: Z-3485AT: Batten Car designed for use with Masts using Z-Spar Full Batten Mast Track that is 24.7mm (<1") wide. Car incorporates fully articulating toggle with 10mm threaded stud (22mm long) for batten attachment. Car rides on Torlon Ball Bearings to provide high strength and low friction at a minimum weight. Extruded Aluminum Car has fully machined races, requiring no end caps. Parts for this Car are listed above.
|
 |
|
|
Headboard Car for Z-Spar RCB Track: Z-3482AT: Headboard Car designed for use with Masts using Z-Spar Full Batten Mast Track that is 24.7mm (<1") wide. Car incorporates pivoting SS channel with shackle for Headboard and Halyard attachment. Car rides on Torlon Ball Bearings to provide high strength and low friction at a minimum weight. Extruded Aluminum Car has removable end caps, for easy ball replacement. Car is 127mm (5") long x 60mm (2 3/8") wide. Headboard Car uses sixty-eight (68) Torlon ball bearings.
|
||
|
|
Ball Bearing Set for Z-3482 Batten Car: Z-BP6M-T68: Replacement ball bearing pack for Z-3482 Batten Car contains sixty-eight (68) 6.4 mm Torlon ball bearings.
|
|
|
Headboard Car for Z-Spar RCB Track: Z-3489AT: Headboard Car designed for use with Masts using Z-Spar Full Batten Mast Track that is 24.7mm (<1") wide. Car incorporates pivoting Aluminum channel with shackle for Headboard and Halyard attachment. Car rides on Torlon Ball Bearings to provide high strength and low friction at a minimum weight. Extruded Aluminum Car has fully machined races, requiring no end caps. Car is 156mm (6 1/8") long x 61mm (>2 3/8") wide. Headboard Car uses sixty-eight (92) Torlon ball bearings.
|
 |
|
|
|
Ball Bearing Set for Z-3489AT Batten Car: Z-BP6M-T92: Replacement ball bearing pack for Z-3489AT Batten Car contains ninety-two (92) 6.4 mm Torlon ball bearings.
|
|
|
Double Headboard Car for Z-Spar RCB Track: Z-3489A2T: Double Headboard Car designed for use with Masts using Z-Spar Full Batten Mast Track. Clear anodized Recirculating Ball Track is 24.7mm (<1") wide. Double Car incorporates pivoting channel with 10mm bolt for Headboard attachment. Car rides on Torlon Ball Bearings to provide high strength and low friction at a minimum weight. Extruded Aluminum Car has removable end caps, for easy ball replacement. Car is 178mm (7") long x 60mm (2 3/8") wide. Each Car uses forty-four (44) Torlon ball bearings. MMM
|
||
|
|
Ball Bearing Set for Z-3489A2T Batten Car: Z-BP6M-T44: Replacement ball bearing pack for Z-3489 Batten Car contains forty-four (44) 6.4 mm Torlon ball bearings. Double Car requires two (2) packs.
|
|
|
|
End Cap for Z-Spar 60mm wide Batten Cars: Z-EC25-1: Replacement End Cap for Z-Spar Batten Cars for Track that is 24.7mm (<1") wide. End Cap is 60mm (2 3/8") wide x (maximum) 40mm (1 9/16") high x 13mm (1/2") thick, and has 5mm (3/16") hole for attachment to Car. 3481 |
 |