Spars, Rigging, and Hardware for Sailboats

Rig-Rite, Inc.
63 Centerville Road, Warwick, RI 02886 USA
Phone: (001) 401-739-1140 -- FAX: (001) 401-739-1149
www.RigRite.com          Ordering/Questions

X Misc IP &
Gooseneck Toggles
Gooseneck Toggles are used to allow universal movement of the Boom both horizontally and vertically, and always have attachment holes at 90 degrees to each other. Some Gooseneck Toggles incorporate Provisions for attachment of the Sail Tack, and some include Reef Hooks. Gooseneck Toggles are listed here by the size of the Vertical Pin with which they attach to the Mast Bracket or Gooseneck Slide. Plain Toggles are listed first, Toggle Assemblies with Tack Attachments and Reef Hooks are listed after them.

Rig-Rite stocks a large variety of Gooseneck Toggles originally produced by many different Spar Builders. As always, there have been many 'specials' produced over the years, if a Gooseneck Toggle you need is not listed here, please contact us with a sketch and complete dimensions. Please note that if a Toggle listed here meets your principal dimensions of height & width, it is frequently possible to modify the hole size by either drilling it out to a larger size, or bushing it down to a smaller one.

Other specialized Gooseneck Toggles and Gooseneck Toggle arrangements, specific to European Spar Builders, are also available.
Isomat Spars use a variety of special plastic Toggle components and SS Toggle Pins, See
Z-Spar Spars use a variety of Cast aluminum Gooseneck Toggles with Metric Pin sizes, See

 
Gooseneck Toggles for a 1/4" Vertical Pin
Stainless Steel Gooseneck Toggle - 3/4" High: K-9267:
SS Gooseneck Toggle attaches directly to any of the Kenyon gooseneck brackets or gooseneck slides designed for a 3/4" Toggle, and to any boom end casting using the Kenyon K-79 or K-80 SS yoke assemblies. Toggle is 3/4" square x 7/8" long with holes for 1/4" vertical and horizontal pins on 3/8" centers.

 

 8750_MastTrack w/Dims
Stainless Steel Gooseneck Toggle - 3/4" High: Sch-45-S0404:
Stainless Steel Gooseneck Toggle is 3/4" high and accommodates 1/4" vertical and horizontal pins. Welded SS Toggle is 3/4" high x 5/8" wide x 1 3/8" (maximum) long, pin holes are on 3/4" centers. Toggle fits a variety of Mast Brackets and Gooseneck Slides designed for a 3/4" Toggle with a 1/4" vertical pin, but is normally used with SS Gooseneck Slide with Spring Pin for 1" x 1/8" Flat Tracked by Pearson especially on Mizzen masts.

 

 8750 MastTrackOrig.jpg (3253 bytes)
Special Deck Collars

 

 7/8" Rolled Sailtrack
 
Gooseneck Toggle, Tack and Yoke Assembly: K-10604:
SS Gooseneck Toggle/Tack & Yoke assembly on 1/2" shaft fits goosenecks with a 1/2" horizontal hole. SS 2 1/2" long shaft comes with SS and nylon washers and cotter pin. Two-position Tack for optimal adjustment with included quick pin. Toggle portion is 1" vertical and attaches to any of the Kenyon gooseneck brackets designed for a 1" Toggle, and most gooseneck slides designed for a 1" Toggle, with a 1/4" pin. As used on Etchells 22.

 

 

SS Bobstay / Whisker Stay Tang w/ 1/2" Pin: Sch :
On board or on boat

 
Gooseneck Toggles for a 5/16" Vertical Pin
Aluminum Gooseneck Toggle - 1 1/2" High: RR-45A-55-1511:
Solid machined Aluminum Gooseneck Toggle is 1 1/2" high and accommodates 5/16" vertical and horizontal pins. Anodized Toggle is 1 1/2" high x 11/16" wide x 1 7/8" (maximum) long, pin holes are on 1 1/8" centers. Toggle fits a variety of Mast Brackets and Gooseneck Slides designed for a 1 1/2" Toggle with a 5/16" vertical pin. m

 

~ Back to Spars Main Page ~

~ Back to Rig-Rite Home Page ~