2" OD Spinnaker Poles & Fittings

Standard 2" OD Spinnaker Pole Tube 2" OD Spinnaker Pole Tube - Clear Anodized: RTA 2-065A-___: 2" OD Spinnaker Pole Tube is stocked, fully anodized, in a variety of lengths up to the maximum listed above. To order, specify tube length.

2" OD Custom Poles and Kits For a quote on Custom Poles or unassembled Kits, specify tube diameter, preferred End Fittings (listed below), Bridle configuration (if any) and contact us. If in doubt about Pole size, end fittings, or optimal configuration, please contact us for recommendations. We have built hundreds of different Spinnaker and Whisker Poles and now have an extensive database of successful pole sizes, in fact, we probably have built a Pole for a boat just like yours.

2" OD Spinnaker Pole End Fittings Pole End Fittings are divided into several categories, listed below. Standard End Fittings are suitable for use on the Outboard end of the Pole, and on the Inboard end when a Ring Car (or a fixed Mast Ring) is used on the Mast. Their use on both ends is required when using an End for End jibing procedure. See also: Spinnaker Cars. Special Outboard Ends are available, including Reaching Strut Ends. End Fitting Adapters, or Collars, allow the use of a larger diameter tube with end fittings designed for a smaller one.

Standard Pole Ends for 2" OD Tube Listed below are Standard End Fittings - These pole ends are suitable for either (or both) ends of a spinnaker pole or whisker pole, or the inboard end of a reaching strut. Their use on both ends is required when using an End for End jibing procedure. When used on the Inboard end a Ring Car (or a fixed Mast Ring) is required on the Mast.

'Ultra' Plastic EL Piston End for 2" OD Tube: EF-200-UXP: Forespar 'Ultra' composite EL Piston End incorporates Spectra loops for attachment of pole lift and foreguy (or bridles), and includes an external Spectra Trip lanyard with terminal eyestrap. Self-Latching EL Piston End has a stainless steel spring-loaded plunger pin that can be engaged simply by pushing onto Ring or Guy. Gray molded End Fitting projects 2 3/4" (maximum) from tube end. F
'Ultra' Plastic EL Piston End for 2" OD Tube: EF-200-UXPL: Forespar 'Ultra' composite EL Piston End incorporates Spectra loops for attachment of pole lift and foreguy (or bridles), and includes an external Spectra Trip lanyard loop as used on Whisker Poles. Self-Latching EL Piston End has a stainless steel spring-loaded plunger pin that can be engaged simply by pushing onto Ring or Guy. Gray molded End Fitting projects 2 3/4" (maximum) from tube end. F3
Aluminum SL Piston End for 2" OD Tube: NF 13520: Cast aluminum Self-Latching Piston End incorporates eyes for attachment of pole lift bridle and foreguy; Piston has hole for attachment of a Trip wire. Self-Latching End has a stainless steel spring-loaded plunger pin that can be engaged simply by pushing onto Ring. Black anodized SL End Fitting projects 4 1/4" (maximum) from tube end. Replacement Piston & Spring Kit is available for this item, Order NF EF-PK-2.
Aluminum Piston End for 2" OD Tube: NF 13620: Cast aluminum Piston End incorporates eyes for attachment of pole lift bridle and foreguy, Piston has hole for attachment of a Trip wire. Piston End has a stainless steel spring-loaded plunger pin that must be manually retracted by pulling on a lanyard, to attach the fitting to a ring or guy. Black anodized end is 5 5/8" long and projects 4 1/2" (maximum) from tube end. This item is no longer available and is shown here for identification only. Replacement Piston & Spring Kit is available for this item, Order NF EF-PK-2.
Aluminum Piston End for 2" OD Tube: SPC P-0101: Original Sparcraft Cast aluminum Piston End incorporates eyes for attachment of pole lift bridle and foreguy, Piston has hole for attachment of a Trip wire. Piston End has a stainless steel spring-loaded plunger pin that must be manually retracted by pulling on a lanyard, to attach the fitting to a ring or guy. Black anodized fitting projects 3 1/2" (maximum) from tube end. #

'Ultra' Plastic Trigger End for 2" OD Tube: EF-200-UTR: Forespar 'Ultra' composite Trigger End incorporates Spectra loops for attachment of pole lift and foreguy (or bridles), and includes an internal Spectra Trip lanyard with terminal eyestrap. Trigger End is like a piston end, except that when the plunger is manually retracted it locks in the open position, waiting for pressure on the Trigger (from a ring, car or guy) to cause it to snap shut. Gray molded end projects 2 3/4" (maximum) from tube end. F
Aluminum Trigger End for 2" OD Tube: NF 10051: Cast aluminum Trigger End incorporates eyes for attachment of pole lift bridle and foreguy, Piston has hole for attachment of an externally mounted Trip wire, allowing for operation while at the fitting. Trigger End is like a piston end, except that when the plunger is manually retracted it locks in the open position, waiting for pressure on the Trigger (from a ring, car or guy) to cause it to snap shut. Black anodized end is 5 5/8" long and projects 4 1/2" (maximum) from tube end. This item is no longer available and is shown here for identification only. Replacement Piston & Spring Kit is available for this item, Order NF EF-PK-2.

Special Outboard Pole Ends for 2" OD Tube Listed below are Special Outboard Pole Ends. Fittings listed here are for Outboard use only, and are not compatible with any standard Mast fittings or Cars.

Reaching Strut End for 2" OD Tube: NF 13820: Cast aluminum Reaching Strut End for 2" OD Tube has sheave for up to 7/16" line. Gray anodized end has heavy finger on upper side and integral bails (top & bottom) for attachment of control lines. Unit projects 5 1/2" from tube end, 1 3/4" OD Sheave bearing surface is 3 5/8" from tube end.

End Fitting Adapters Adapting Collars allow End Fittings to be used with larger diameter tube. This sometimes results in a net weight savings, and often allows for configurations otherwise unavailable. Please Note that adapting collars can be used together, but have ID's designed for End Fittings and can not be used for sleeving two sizes of tubing together. As always, special sizes are available on a Custom basis.
2" End Fitting Adapter for 2 1/2" OD Tube - Plastic: AC2-25U: 'Ultra' Composite Plastic Adapting Collar allows use of any End Fitting for 2" OD Standard Spinnaker Pole Tube with 2 1/2" OD Standard Spinnaker Pole Tube. Gray Collar is 2" long and projects 5/8" from tube end. F
2" End Fitting Adapter for 2 1/2" OD Tube: AC2-25AX: Cast Aluminum Adapting Collar allows use of any End Fitting for 2" OD Standard Spinnaker Pole Tube with 2 1/2" OD Standard Spinnaker Pole Tube. Gray anodized Collar is 2 1/2" long and projects 1 1/4" from tube end. F

1 3/4" End Fitting Adapter for 2" OD Tube: AC175-2AX: Cast Aluminum Adapting Collar allows use of any End Fitting for 1 3/4" OD Standard Spinnaker Pole Tube with 2" OD Standard Spinnaker Pole Tube. Gray anodized Collar is 1 7/16" long and projects 7/16" from tube end. F

Your cart

Spars, Rigging, and Hardware for Sailboats

Standard 2" OD Spinnaker Pole Tube Measurements: 2.00" OD x 1.87" ID (50.8mm x 47.5mm) Wall Thickness: .065" Weight/ft.: .47 lbs. Moments of inertia: Circumference: 6.28" Alloy: 6063-T6 Stock Lengths: Up to 20' Common Boat usage: 18' - 25' LOA
2" OD Standard Spinnaker Pole Tube is used in a variety of applications, including Spinnaker Poles, Reaching Struts, and Whisker Poles. Standard Pole Fittings for this tube size are listed below.