1 1/2" OD Spinnaker Poles & Fittings

Standard 1 1/2" OD Spinnaker Pole Tube 1 1/2" OD Spinnaker Pole Tube - Clear Anodized: RTA 1.50-065A-___: 1 1/2" OD Spinnaker Pole Tube is stocked, fully anodized, in a variety of lengths up to the maximum listed above. To order, specify tube length.

1 1/2" OD Spinnaker Pole End Fittings Pole End Fittings are divided into several categories, listed below. Standard End Fittings are suitable for use on the Outboard end of the Pole, and on the Inboard end when a Ring Car (or a fixed Mast Ring) is used on the Mast. Their use on both ends is required when using an End for End jibing procedure. See also: Spinnaker Cars. End Fitting Adapters, or Collars, allow the use of a larger diameter tube with end fittings designed for a smaller one.

Standard Pole Ends for 1 1/2" OD Tube

'Ultra' Plastic EL Piston End for 1 1/2" OD Tube: EF-150-UXP:
Forespar 'Ultra' composite EL Piston End incorporates Spectra loops for attachment of pole lift and foreguy (or bridles), and includes an external Spectra Trip lanyard with terminal eyestrap. Self-Latching EL Piston End has a stainless steel spring-loaded plunger pin that can be engaged simply by pushing onto Ring or Guy. Gray molded End Fitting projects 3 1/4" (maximum) from tube end. F
Aluminum SL Piston End for 1 1/2" OD Tube: NF 13515: Cast aluminum Self-Latching Piston End incorporates eyes for attachment of pole lift bridle and foreguy; Piston has hole for attachment of a Trip wire. Self-Latching End has a stainless steel spring-loaded plunger pin that can be engaged simply by pushing onto Ring. Black anodized SL End Fitting projects 4 1/4" (maximum) from tube end.
Aluminum Piston End for 1 1/2" OD Tube: NF 13615: Cast aluminum Piston End incorporates eyes for attachment of pole lift bridle and foreguy, Piston has hole for attachment of a Trip wire. Piston End has a stainless steel spring-loaded plunger pin that must be manually retracted by pulling on a lanyard, to attach the fitting to a ring or guy. Black anodized end is 5 1/4" long and projects 4 1/2" (maximum) from tube end. This item is no longer available and are shown here for identification only.
Self-Latching SS End for 1 1/2" OD Pole: RF 601: Self-Latching Piston End allows for easy single-handed attachment by pressing against Ring or Guy. Unit is made of chrome plated cast bronze with Stainless Steel straps, and fits the outside of 1 1/2" diameter poles. Unit is 6" long, projects approximately 2 1/4" beyond pole end and is attached to pole with (6) 3/16" (#10) screws or (3) bolts.

End Fitting Adapters Adapting Collars allow End Fittings to be used with larger diameter tube. This sometimes results in a net weight savings, and often allows for configurations otherwise unavailable. Please Note that adapting collars can be used together, but have ID's designed for End Fittings and can not be used for sleeving two sizes of tubing together. As always, special sizes are available on a Custom basis.
1 1/2" End Fitting Adapter for 1 3/4" OD Tube: AC150-175AX:
Cast Aluminum Adapting Collar allows use of any End Fitting for 1 1/2" OD Standard Spinnaker Pole Tube with 1 3/4" OD Standard Spinnaker Pole Tube. Gray anodized Collar is 1 1/8" long and projects 1/4" from tube end. F

Your cart

Spars, Rigging, and Hardware for Sailboats

Standard 1 1/2" OD Spinnaker Pole Tube Measurements: 1.50" OD x 1.37" ID (38.1mm x 34.8mm) Wall Thickness: .065" Weight/ft.: .345 lbs. Moments of inertia: Circumference: 4.71" Alloy: 6063-T6 Stock Lengths: Up to 27' 4" Common Boat usage: 14' - 21' LOA
1 1/2" OD Standard Spinnaker Pole Tube is used in a variety of applications, including Spinnaker Poles, Reaching Struts, and Whisker Poles. Standard Pole Fittings for this tube size are listed below. This Tube is also used for small boat Booms, See Kenyon Spars 1 1/2" Round Boom Section.