Spars, Rigging, and Hardware for Sailboats

Rig-Rite, Inc.
Phone: (001) 401-739-1140 -- FAX: (001) 401-739-1149
www.RigRite.com        Spartan Ordering/Questions

Spartan Spars CD-2 Boom Section


Spartan Spars CD-2 Boom
Measurements: (OD) 3.75" x 2.25"
Wall Thickness: .100"
Weight/ft.: 1.30 lbs.
Moments of inertia: Ixx = 1.32", Iyy = .600"
Circumference: 9 5/8"
Alloy: 6061-T6
Standard Lengths: 11'7"
Sail slides: 1/2" round slugs (A018, A118) or 1/2" boltrope
Common Boom usage: Cape Dory Typhoon Senior, Cape Dory 22, Cape Dory 25*, Cape Dory 25D, Cape Dory 26;

CD-2 Boom Section


Spartan CD-2 Boom Section

CD-2 Boom Section - Clear Anodized: SP-CD2CA-___:
Spartan CD-2 Section Boom Tube is stocked in a variety of lengths (listed above) fully anodized, it can also be cut to shorter lengths. To order, specify length.
Sections can also be milled for the sail entrance or other components if necessary, painted finishes and other lengths are available on special order, Please specify. If you require a complete Boom Assembly, you can select from components below and contact us with specifications.
 


CD-2 Standard Boom Hardware
Listed below are parts specific to the Spartan CD-2 Boom Section. There are many parts for unusual configurations that are not listed here. If you require CD-2 Section Boom Components not listed here please contact us with details. Please note: As principal dimensions of the Spartan Spar CD-2 Section are equivalent to those of Kenyon Spar's D-Section, all Kenyon D-Section Boom Components will also fit the CD-2 Boom Section.

All Aluminum Castings listed below are carefully hand finished and coated with a baked-on Black Epoxy (to retard corrosion) as Standard. Castings are available Clear Anodized at additional cost, add CA to part number.
 


CD-2 Gooseneck Assemblies & Parts
 
CD-2 Gooseneck Ass'y Complete w/ 1/2" Slide: SP-073FS:
Cast aluminum boom end fitting includes captive SS tack pin and SS yoke, K-80, 1" SS Toggle, K-1993, and 1/2" SS Gooseneck Slide, SP-074. Fits CD-2, CD-3 and all mast sections using 1/2" round slugs or boltrope.  p

 

SP-073FS

CD-2 Gooseneck Ass'y w/ Tack & 1" Toggle: SP-073F:
Heavy-duty cast aluminum Gooseneck End incorporates a 1/4" tack pin and includes fixed SS yolk and 1" Toggle, K-1993. Designed for use with SS Slide SP-074, or a fixed Gooseneck Bracket such as SP-11206. As SP-073FS, above, but without slide (SP-074). p

 

SP-073F
CD-2 Roller Reefing Gooseneck Ass'y w/ 1/2" Slide: SP-073RS:
Heavy-duty cast aluminum Gooseneck End incorporates a 1/4" tack pin and includes SS spring loaded roller reefing assembly and 1" toggle. Pulling aft on the boom allows it to be rotated with the sail, releasing it locks it into place. Requires use of Outhaul End with pivoting tangs SP-107-2. p

 

SP-073RS

Roller Reefing Gooseneck Ass'y w/ Tack & 1"Toggle: SP-073R:
Heavy-duty cast aluminum Gooseneck End incorporates a 1/4" tack pin and includes SS spring loaded roller reefing assembly and 1" toggle. Pulling aft on the boom allows it to be rotated with the sail, releasing it locks it into place. Designed for use with SS Slide, SP-074, or a fixed Gooseneck Bracket such as SP-11206. Roller-Reefing mechanism requires use of Outhaul End with pivoting tangs, SP-107-2, or similar. As SP-073RS, above, but without slide (SP-074).

 

SP-073R
 

CD-2 Gooseneck Casting w/ Tack Pin: SP-073C:
Black Epoxy coated Gooseneck casting with tack pin only, as used in the assemblies listed above. p

 

SP-073C
Gooseneck Slide: SP-074:
SS Gooseneck Slide accepts 1" toggle and has a welded ring for downhaul attachment. Includes 1/4" vertical pin. K-1685A p


SP-074
SS Gooseneck Toggle - 1": K-1993:
SS Gooseneck Toggle attaches directly to gooseneck brackets or SS gooseneck slides designed for a 1" Toggle, and to any boom end casting using the K-80, or K-8890 SS yoke assemblies. Toggle is 1" square x 1 1/8" long with 1/4" holes at 90 degrees to each other on 1/2" centers.

 

K-1993
SS Yoke Ass'y for 1" Toggle: K-80A:
SS Yoke attaches to various boom end castings with a 3/8" bolt, and to the 1" SS Toggle, K-1993, with a 1/4" SS bolt and locknut (included). Yoke is formed from 1" wide stock and is 1 3/16" wide (outside), and 1 1/32" wide (inside), 1/4" hole centers are 13/16" from bottom inside.

 

K-80
SS Roller-reefing Yoke Ass'y for 1" Toggle: K-8890A:
SS spring-loaded roller-reefing yoke assembly for use with boom end castings that have a 1/2" hole centered in a 1 1/4" square recess. Attaches to 1" SS Toggle, K-1993, with a 1/4" SS bolt and locknut (included). Post is 1/2" diameter x 3 1/2" long. Includes SS Spring, SS washers, and cotter pin.

 

K-8890A
CD-2 Gooseneck Ass'y - No Tack: SP-118:
Heavy-duty cast aluminum Gooseneck End without Tack provision incorporates fixed SS yolk with 5/16" bolt (included) for toggle attachment. Designed for use with CD-3.5 Gooseneck Bracket, SP-454.

 

CD-2 Gooseneck Casting - No Tack: SP-118C:
As SP-118, above, but casting only, for replacement use. Incorporates 1/2" hole in center of 1 1/4" wide x 1 1/8" high recess.

 

CD-2 Gooseneck Casting for Club Boom: SP-565:
Elongated Gooseneck casting is commonly used with Jib Club Booms using the Bronze Pedestal Base, SP-566. Clear anodized casting has 3/8" hole for bolt attachment. Unit is also available complete with yoke and toggle to fit the variety of Pedestal arrangements used over the years, please supply measurements of existing configuration.

 

SP-565


CD-2 Outhaul Assemblies & Parts
CD-2 Outhaul Casting: SP-076:
Heavy-duty Black Epoxy coated cast aluminum Outhaul End has tab with 3 holes for outhaul and topping lift attachment.

 

SP-076

CD-2 Outhaul Ass'y w/ Tang: SP-076-1:
Heavy-duty cast aluminum Outhaul End with attachment points for outhaul and topping lift. Includes single pivoting tang for mainsheet or topping lift attachment.

 

CD-2 Outhaul Ass'y w/ Two Tangs: SP-076-2:
Heavy-duty cast aluminum Outhaul End with attachment points for outhaul and topping lift. Includes two pivoting tangs for mainsheet and topping lift attachment. For use with roller reefing gooseneck, SP-073R.

 

Mainsheet Tang for CD-2 Boom: SP-261:
Flat Mainsheet Tang attaches to Boom end casting using a 3/8" bolt. For use with Spartan CD-2, Kenyon D-Section, and similar sized booms. Mainsheet Tang is 5" long x 1" wide x .076" thick with (1) 3/8" mounting hole and a 1/2" x 1" slot for attachment of Mainsheet block.

 


CD-2 Boom Accessories
Outhaul Slides
A variety of Outhaul Slides are available to fit the 1/2" Boltrope groove in the CD-2 Boom Section.
See Outhaul Slides for 1/2" Boltrope Groove.

 

Boom Bail - 1/4" x 2 1/4" wide: K-10456:
Heavy SS Boom Bail made from 1/4" rod is designed to be attached with (1) 1/4" SS bolt and nut. Formed at 2 1/4" wide, width can be varied to fit larger or smaller sections. Bail length, from bolt center, is 2 1/2". For use with CD-2 Boom.

 

K-10456
Boom Bail Bolt Ass'y - 1/4" for CD-2 Boom: K-10456BA:
Boom Bail bolt assembly includes 1/4" SS bolt x 2 3/4", with locknut, and nylon washers to prevent bail from damaging boom surface as it pivots. 

 

K-10456BA
Boom Bail - 3/8" x 2 1/4" wide: K-10456H:
Heavy SS Boom Bail made from 3/8" rod is designed to be attached with (1) 3/8" SS bolt and nut. Formed at 2 1/4" wide, width can be varied to fit larger or smaller sections. Bail length, from bolt center, is 3 1/2". For use with CD-2 Boom. 10

 

Boom Bail Bolt Ass'y - 3/8" for CD-2 Boom: K-10456HBA:
Boom Bail bolt assembly includes 3/8" SS bolt x 3", with locknut, and nylon washers to prevent bail from damaging boom surface as it pivots.

 

Vang Bracket for CD-2 Boom: K-1757:
SS Vang Bracket is contoured to fit CD-2 boom and has welded triangle with 1/2" hole for attachment of vang tackle. Unit is 2 1/2" long, and fastens with (6) 3/16" (#10) fasteners.

 

K-1757
Boom Vang Ball Attachment Plate for CD-2 Boom: K-2182:
Formed SS plate for attachment of Boom Vang with 1/8" wire swage ball. Allows for quick attachment and removal of Boom Vang, raised channel design allows easy installation without milling slot in boom. Channel projects approximately 3/8" from underside of Boom when installed. Formed Stainless Steel plate is 2" long x 1 7/8" high. Fastens with (6) 3/16" (#10) screws or rivets.

 

Boom Vang Ball Attachment Plate for Flush Mounting: K-2182F:
Formed SS plate for attachment of Boom Vang with 1/8" wire swage ball. Allows for quick attachment and removal of Boom Vang, flush mounting design allows use with Roller-Reefing booms. Base is curved to fit a variety of Boom Sections, narrow profile allows it to be bent to fit others. Formed Stainless Steel plate is 3" long x 1 1/2" wide. Mounting requires 3/8" wide x 1 1/4" long slot in Boom. Fastens with (6) 3/16" (#10) screws or rivets.

 

Sch 90-54XS

 

Boom Vang Wire Pennant w/ Swage Ball: K-2182WP:
Wire Pennant for attachment of Boom Vang to Boom Vang Ball Attachment Plate. Pennant is 1/8" wire with swage ball and shank (MS20664-4) on one end and a nicopress and thimble on the other. Thimble allows attachment of any upper Vang block. Assembly is 6" long. Ball is suitable for all Ball Attachment Plates with a slot that is 1/4" wide or less.

 

 

 

Cheek Block w/ Curved Base: K-140X:
Cheek Block with curved base is used on smaller Booms for Outhaul and Reef lines. SS Cheek Block has 1 1/16" OD Delrin Sheave suitable for use with line up to 3/8" diameter. Base is 3 3/16" long x 7/8" wide, and fastens to spar with (4) 3/16" (#10) RH screws on 2 11/16" (horizontal) and 1/2" (vertical) centers.

~ Back to Spartan Main Page ~

~ Back to Rig-Rite Home Page ~