|
|
|
Spartan Mast Tangs Spartan Stainless Steel Tangs are designed for use attaching rigging end fittings with standard pin sizes, to a wide range of Mast Sections. All Tangs are stamped from SS plate, highly polished, and carefully finished to remove any sharp edges. See also, Tangs Main Page. |
||
|
|
||
|
Forestay/Shroud Tang for 1/4" Pin: SP-201:
Lightweight SS Shroud Tang mounts with (4) 3/16" screws or rivets, for use with a Shroud up to 5/32" diameter using standard Aircraft Fork. Tang is 3 1/4" long x 3/4" wide x .056" with (4) 3/16" mounting holes and (1) 1/4" Pin Hole. Fastener holes are 3/8" apart. Features curved mounting surface for use in a wide variety of Forestay and Shroud applications. As used for Forestay Tang on Cape Dory Typhoon and other fractional rigs.
|
|
|
|
Shroud Tang for 1/4" Pin: SP-209:
Lightweight SS Shroud Tang mounts on a 3/8" bolt, for use with a Shroud up to 5/32" diameter using standard Aircraft Fork. Tang is 3 3/4" long x 1 1/16" wide x .070" with (1) 3/8" mounting hole and (1) 1/4" Pin Hole. Hole centers are 2 3/4" apart.
|
 |
|
|
Shroud Tang for 5/16" Pin: SP-202:
SS Shroud Tang mounts on a 3/8" bolt, for use with a Shroud up to 7/32" diameter using standard Aircraft Fork. Tang is 3 3/4" long x 1" wide x .120" with (1) 3/8" mounting hole and (1) 5/16" Pin Hole. Hole centers are 2 3/4" apart. Replaced by K-363C (identical, but .125" thick).
|
||
|
Fixed Shroud Tang for 3/8" Pin: SP-204:
SS Shroud Tang was designed for use with Shrouds up to 7/32" diameter using standard Aircraft Fork. Tang is 6 1/4" long x 1 1/4" wide x .120" with (2) 3/8" mounting holes and (1) 3/8" Pin Hole. Bolt hole centers are 1 7/8" apart, Pin Hole center is 3 1/8" from lower bolt. Assembly attaches to the mast with (2) 3/8" bolts. Mounting requires (2) 3/8" holes in side of mast.
|
 |
|
|
Double Shroud Tang for 1/4" Pins: SP-203:
SS Double Shroud Tang mounts on a 3/8" bolt, for use with 2 Shrouds up to 5/32" diameter using standard Aircraft Forks. Tang is 4 1/4" long x 1" wide (at top) x 1 7/8" wide (at bottom) x .120" with (1) 3/8" mounting hole and (2) 1/4" Pin Holes. Pin Hole centers are 3 3/16" (vertical) from mounting hole and are 1 1/16" (horizontal) apart. Used as Lower Shroud Tang with SP-302 and SP-056 Spreader Bases, and in a variety of other applications. As Sch 85-54.
|
|
|
|
Double Shroud Tang for 5/16" Pins, 3/8" bolt: SP-205:
SS Double Shroud Tang mounts on a 3/8" bolt, for use with 2 Shrouds up to 7/32" diameter using standard Aircraft Forks. Tang is 6 5/8" long x 1" wide (at top) x 2 1/2" wide (at bottom) x .120" with (1) 3/8" mounting hole and (2) 5/16" Pin Holes. Pin Hole centers are 5 1/2" (vertical) from mounting hole and are 1 1/2" (horizontal) apart. Used as Lower Shroud Tang with SP-089 Spreader Bases, and in a variety of other applications. As Sch 85-55.
|
|
|
|
Double Shroud Tang for 5/16" Pins, 1/2" bolt: SP-205-8S:
SS Double Shroud Tang mounts on a 1/2" bolt, for use with (2) Shrouds up to 7/32" diameter using standard Aircraft Forks. Tang is 5" long x 1 1/2" wide (at top) x 2 1/2" wide (at bottom) x .120" with (1) 1/2" mounting hole and (2) 5/16" Pin Holes. Pin Hole centers are 3 3/4" (vertical) from mounting hole and are 1 1/2" (horizontal) apart.
|
|
|
|
Fixed Clevis Tang w/ 1/2" Pin: SP-206:
SS Upper Shroud Tang Assembly was designed for use with Shrouds up to 9/32" diameter using standard Marine Eyes. Tang is 6 7/8" long x 1 1/4" wide x .120" with (1) 1/2", and (1) 3/8" mounting hole and includes (1) 1/2" Clevis Pin. Tang Assembly mounts with (1) 1/2" bolt and (1) 3/8" bolt on 1 7/16" centers; Pin center is 4" from lower bolt. Especially suitable for use in Upper Shroud applications as the 2 bolts allow no fore and aft movement, it is also suited for other applications where the tang should not be allowed to pivot.
|
 |
|
|
Double Lower Shroud Clevis Tang Set w/ 1/2" Pins: SP-753K: SS Double Lower Shroud Tang Set was designed for use with 4 Lower Shrouds up to 9/32" diameter using standard Marine Eyes. Set includes (2) Tangs (SP-753P&S) w/ 1/2" Clevis Pins. Double Tang is 6" long x 2 1/4" wide x .120" with (1) 3/4" mounting hole. Pin centers are 3 1/8" (upper) and 4 1/4" (lower) from mounting hole and are 1 1/2" (diagonally) apart. Mounting requires (1) 3/4" hole in each side of mast. Commonly used with SP-753BPA Backing Plate Assembly with Flange Bushings, below.
|
|
|
|
Backing Plate Ass'y w/ Flange Bushings: SP-753BPA:
Recommended for standard applications, this Assembly allows for attachment of SP-753K Tang Set with (2) 1/2" bolts. Includes (2) Tapered Bearing Plates (K-11216-S1), and (2) 3/4" OD Flange Bushings (K-10455S). Mounting requires (1) 1/2" and (1) 3/4" hole in each side of mast. Used with SP-765 and SP-766 Spreader Bases, and in a variety of other applications.
|
|
|
|
Tapered SS Bearing Plate w/ 3/4" hole: K-11216-S1:
Tapered SS Bearing Plate has (1) 1/2" hole and (1) 3/4" hole for use with bolts of those sizes, or with SS Flange Bushings and smaller bolts. Tapered Plate is 3 1/2" long x 1" wide (at top) x 2" wide (at bottom) x 3/32" (.098") thick, with (2) holes on 1 3/4" centers, and is contoured for use with most Mast Sections.
|
|
|
|
Flange Bushing - 3/4" OD x 1/2" ID: K-10455S:
SS Flange Bushing is 3/4" OD x 1/2" ID. Used with a 1/2" bolt it replaces a 3/4" bolt in Shroud Tang applications to achieve significant weight reduction without any attendant reduction in bearing surface. 3/4" OD Flange Bushing is 3/4" long, Flange Head is 7/8" diameter x 1/8" thick. XXP |
 |
|
~ Home ~
