|
|
| Spartan Spars SP-165 Airfoil Spreader Section Measurements: 4.50" x 1.50" (4 1/2" x 1 1/2") Wall Thickness: .094" Weight/ft.: 1.12 lbs. Moments of inertia: Ixx = 1.30" Iyy = .228" Alloy: 6061-T6 Common Boat usage: C&C 29*; Cape Dory 36, 40; Pearson 365, 40, 424; Tartan; Sound Spars; & others. |
 |
| SP-165 Airfoil Spreader Section Hardware | |
| SP-165 Spreader Section: SP-165XR-____: Spartan SP-165 Spreader Extrusion is stocked Raw (mill finish) and is available in lengths up to 14'. To order: specify length.
|
|
| SP-165 Tapered Spreader Assembly: SP-165TA-____: Spartan SP-165 Spreaders are normally tapered, and use a special welded aluminum 'twist-lock' spreader tip, which captures the shroud without using seizing wire. Other Tips are available. Standard finish is clear anodized, specify color if painted finish is required. Standard Lengths are 3' 9 1/4" and 4' 4", but finished spreaders are available in any length. To order: Specify maximum length from inboard end to shroud bearing surface, spreader base configuration, and finish.
|
 |
| SP-165 Tapered Spreader Tip: SP-165TL: Special 'twist-lock' spreader tip for spreader tapered to 2 3/4" features slot for up to 3/8" shroud. Shroud is secured without seizing wire, by inserting it horizontally into Spreader Tip and then 'twisting' it to lie in line with the mast. Tip measures 2 3/4" x 1", and extends shroud seat 1/2" beyond spreader tube. Cast aluminum Spreader Tip has uncoated Aluminum finish for use in welded applications.
|
|
| SP-165 Inboard Spreader End - Special, Large: K-11480-5SL: Inboard Spreader End is used for masts with SS Spreader Brackets or welded aluminum spreader bases. Aluminum spreader end is welded in a slot cut in SP-165 Spreader. Tapered Aluminum plate is 3/8" thick x (maximum) 7 1/4" wide x 5" long, and features integral etch lines to line up with end of SP-165 Spreader. Mounts to mast with (2) 1/2" holes on 5 3/4" centers, holes are 3/4" from end of plate. Plate has uncoated Aluminum finish. SoundSpar
|
 |
|
Spreader Bases for SP-165 Airfoil Spreaders Spartan SP-165 Airfoil Spreaders are normally used with Spreader Bases which are formed to fit specific Mast Sections. A variety are listed below. |
|
| CD-5 Spreader Base - Port: SP-164P: CD-5 Spreader Base - Starboard: SP-164S: Cast aluminum Spreader Base for CD-5 Mast Section fits flush with the mast surface and attaches with (6) 1/4" FH screws. For use with 4 1/2" Airfoil Spreaders, SP-165. Cast in 356 Aluminum with clear anodized finish.
|
 |
| CD-5 Spreader Base w/ Tang Attachment - Port: SP-164-1P: CD-5 Spreader Base w/ Tang Attachment - Starboard: SP-164-1S: Cast aluminum Spreader Base for CD-5 Mast Section fits flush with the mast surface and attaches with (6) 1/4" FH screws and a 1/2" bolt. Unique and sleek design allows for use of the same 1/2" bolt as an attachment point for a lower shroud tang (SP-753). For use with 4 1/2" Airfoil Spreaders, SP-165. Cast in 356 Aluminum with clear anodized finish.
|
|
| Sound Spar 8755 / MM 8348T Spreader Base for SP-165, Port: SS 8755SBC-P: Sound Spar 8755 / MM 8348T Spreader Base for SP-165, Starboard: SS 8755SBC-S: |
|
| Cast Aluminum Spreader Base used on Sound Spar 8755 Mast Section (8.75" x 5.50"),
and on MetalMast 8348T (8.30" x 4.81") Teardrop Mast Section with SP-165 Spreaders.
Spreader fits over male stud on Base, Teardrop shaped Base is 6" wide x 3 1/4"
high. Normally attaches to Mast with (6) 1/4" RH screws, but due to mounting variations castings
are supplied raw, without holes for fasteners.
As used on Pearson 10M, 365, 386, and others.
|
|
| C&C Spreader Base for SP-165, Port: CC SPB4-29P: C&C Spreader Base for SP-165, Starboard: CC SPB4-29S: Cast Aluminum Spreader Base used on C&C Masts with SP-165 Spreaders. Spreader fits over male stud on Base. Base is 5 1/4" wide x 3" high with deep curve to fit C&C Mast Sections. Attaches to Mast with (6) 1/4" RH screws. As used on C&C 29 and others.
|
|
|
SS Spreader Base w/ 3/8" Pin, Port Aft: SS 8755SBS-6PA: SS Spreader Base w/ 3/8" Pin, Starboard Aft: SS 8755SBS-6SA: Stainless Steel Spreader Bases used on Sound Spar 8755, and other Mast Sections, with SP-165, SP-512, and other Spreaders using a 1/4" or 5/16" thick Inboard Spreader End Plate, similar to K-11480-5SL, above. SS Rectangular Base is 2 1/2" high x 2 3/16" wide, and attaches to Mast with (4) 1/4" RH screws on 1 3/4" (vertical) x 1 1/2" (horizontal) centers. Spreader Inboard End is attached to Base with a 3/8" clevis pin (included). Bases are used in pairs, with a Port Aft and a Starboard Aft version on each side of the Mast. (Port Aft = Starboard Forward, Starboard Aft = Port Forward). SS8755S
|
|
|
SS Spreader Base w/ 1/2" Pin, Port Aft: SS 8755SBS-8PA: SS Spreader Base w/ 1/2" Pin, Starboard Aft: SS 8755SBS-8SA: Stainless Steel Spreader Bases used on Sound Spar 8755, and other Mast Sections, with SP-165 and other Spreaders using the K-11480-5SL Inboard Spreader End, above. SS Base is 3" square and attaches to Mast with (4) 1/4" RH screws on 2 1/8" (vertical & horizontal) centers. Spreader Inboard End is attached to Base with a 1/2" clevis pin (included). Bases are used in pairs, with a Port Aft and a Starboard Aft version on each side of the Mast. (Port Aft = Starboard Forward, Starboard Aft = Port Forward). As used on Pearson 36, 424, and others. P1184SA SS8755L |
|
