Spars, Rigging, and Hardware for Sailboats

Rig-Rite, Inc.
Phone: (001) 401-739-1140 -- FAX: (001) 401-739-1149
www.RigRite.com        Spartan Ordering/Questions

1 1/4" OD Round Spreaders & Hardware


Spartan Spars 1 1/4" Round Spreader Section - SP-090
Measurements: 1 1/4" OD x 1" ID
Wall Thickness: .125"
Weight/ft.:  .519 lbs.
Alloy: 6061-T6
Stock Length: 18'
Common Boat usage: Cape Dory 27*, 28*, 30*;
1 1/4" x 1" round tube

1 1/4" OD Round Spreader Tube
1 1/4" Round Spreader Tube: SP-090TC-___:
Spartan 1 1/4" OD x 1" ID Spreader Tube is stocked in a clear anodized finish and is available in 3' 1" (37"), 4', 6', and 18' lengths, or can be cut to other lengths. To order: specify length.
 

1 1/4" OD Round Spreader Assemblies & Parts
1 1/4" Round Spreader Assembly x 37 1/2" long: SP-090AS:
1 1/4" Round Spreader Assembly x 48 1/2" long: SP-090A-48:
Spartan SP-090 Spreader is 1 1/4" OD x 1" ID, and has Aluminum Tip, SP-090T, with hole for seizing wire (included). Clear anodized 1 1/4" Spreader Assemblies are 5/8" (overall) longer than mast to wire measurement.

 

SP-090A

 

1 1/4" Round Spreader Assembly - Special: SP-090A-___:
Spartan SP-090 Spreader is 1 1/4" OD x 1" ID and has Aluminum Tip, SP-090T, with slot for upper shroud, and hole for seizing wire (included). Finished spreaders are available in any length, standard finish is clear anodized, specify color if painted finish is required. To order: specify maximum length from inboard end to shroud bearing surface, and finish.

 


1 1/4" Round Spreader Tip: SP-090T:
Clear anodized Aluminum Spreader Tip for 1 1/4" OD x 1" ID Spreader features slot for up to 1/4" shroud. Lightweight, compact version replaces earlier Cast style and features cross-hole for seizing wire. New-style turned Tip extends shroud seat 1/2" beyond spreader tube, unit projects 1 1/16" (maximum) beyond spreader tube and is carefully rounded to reduce sail chafe. As K-8609.   cast was 3/4",1 3/8"

 

Spreader Tip for Tapered Spreader (1 1/4" OD Outboard): K-10127:
Aluminum Spreader Tip for Kenyon Swaged Taper Spreader fits Spreader End that has been reduced to 1 1/4" OD x 7/8" ID. Cast Spreader Tip has slot for up to 9/32" diameter shrouds and features cross-hole for seizing wire. This part is no longer available and is shown here for identification only. The SP-090T, above, can be used by filing the spreader ID.

 

Spreader Boot Pair for 1 1/4" OD Spreader: SP-057B:
Spreader Boot for 1 1/4" OD Spreader is designed to reduce sail chafe. White Rubber Boot is attached to Spreader and Shroud using wire ties or Rigging Tape. Sold in Pairs only, they are (maximum) 5 3/4" long.

 


Spreader Bases for 1 1/4" Round Spreaders
Listed below are Spreader Bases commonly used with 1 1/4" OD Round Spreaders. Some Spreader Bases are commonly used with Compression Tubes fitting over one or more mounting bolts, See Compression Tubes.
 
CD-4 Spreader Base - Triangular: SP-089:
Triangular Cast aluminum Spreader Base for 1 1/4" Spreader fits CD-4 and RR#8 Mast Sections. Attaches to Mast with (3) 1/4" FH machine screws and a 3/8" bolt. Unique and sleek design allows for use of the same 3/8" bolt as an attachment point for a lower shroud tang, SP-205. Used for rigs with in-line spreaders, base has 5-degree vertical lift. Please Note: If ordering this item as a replacement part, please verify OD of Spreaders as early units, SP-089LX, were produced for 1 5/16" OD Spreaders.

 

SP-089
CD-4 Spreader Base - Square: SP-089-0:
Older style, Square Cast aluminum Spreader Base for 1 1/4" Spreader fits CD-4 and RR#8 Mast Sections. Attaches to Mast with (4) 1/4" RH machine screws and a 3/8" bolt. Design allows for use of the same 3/8" bolt as an attachment point for lower shroud tang, SP-205. Used for rigs with in-line spreaders, base has 5-degree vertical lift. Please Note: If ordering this item as a replacement part, please verify OD of Spreaders as early units were produced for 1 5/16" OD Spreaders.  S55-34
SP-089-0

~ Back to Spreaders Main Page ~

~ Back to Spartan Main Page ~

~ Back to Rig-Rite Home Page ~