Spinnaker Cars for Recirculating Ball Tracks

These Spinnaker Cars are designed to fit on a variety of Recirculating Ball (RCB) Tracks, and are held in place on the track by means of a line control system. The use of these Ball-Bearing Cars (on special Tracks) minimizes friction on the Track, allowing for greater ease of movement under load. These Spinnaker Cars are shipped on a short length of loading Track which keep the Ball-Bearings in place until Car is loaded on destination Track. Cars must not be removed from Track, as doing so will allow the Ball-Bearings to escape - rendering the Car inoperative as well as making a mess! Loading Track should be saved for future Car removal or service. All Cars include shackles or other attachments for Control Lines or Blocks. Ring Cars are used for Poles with standard Piston or Trigger pole ends, Pin, or Bell Cars are used to fit the variety of special inboard Spinnaker Pole Ends available. Please note that Ring Cars are not designed for, or recommended for vertical pole stowage applications.

Spinnaker Cars for Recirculating Ball (RCB) Tracks For NF 1100 RCB Track For Harken Small Boat (#373, or #2720) RCB Track For Harken Midrange (#1602, or #1616) RCB Track For Harken Big Boat (#516, or #758) RCB Track For Z-Spar RCB Track Replacement Bayonet Pins & Toggles Replacement Metric Bell Fittings

Spinnaker Cars for NF 1100 RCB Track
Spinnaker Ring Car for NF 1100 RCB Track: NF 1182: Recirculating Ball Spinnaker Car to fit NF 1100 RCB Track. Car has large SS Ring assembly screwed to extruded Aluminum Body. Car is 4 9/16" long x 2 3/8" wide, SS Ring is 7/16" x 1 3/4" ID, and projects 3 1/8" (maximum) from Track surface. NF 1182 Car uses (60) 1/4" Torlon Balls. Nicro-Fico NF 1100 Recirculating Ball (RCB) Track measures 15/16" (26mm) across the top.

Spinnaker Cars for Harken Small Boat Track
Harken Small Boat Recirculating Ball (RCB) Track measures 7/8" (22mm) across the top. Harken Small Boat Cars use 1/4" Torlon Balls.
Spinnaker Ring Car for Harken Small Boat RCB Track: Har 780: Recirculating Ball Spinnaker Car to fit Harken Small Boat RCB Track. Car has cast SS Ring assembly screwed to extruded Aluminum Body. Car is 4 3/8" (110mm) long x 2 3/16" (56mm) wide, SS Ring is 3/8" x 1 1/4" ID, and projects 1 3/4" (maximum) from Track surface. Har 780 Car uses (64) 1/4" Torlon Balls.		R
	Replacement Balls for Harken Small Boat Spinnaker Car: Har 780-BP:
	Replacement Ball Bearing Pack for Harken Small Boat Spinnaker Cars. Pack includes (64) 1/4" Torlon Balls, for use with Har 780 Car.

Spinnaker Cars for Harken Midrange Track
Harken Midrange Recirculating Ball (RCB) Track measures 1 1/16" (27mm) across the top. Harken Midrange Cars use 5/16" Torlon Balls.
	Replacement Balls for Harken Midrange Spinnaker Cars: Har 781-BP:
	Replacement Ball Bearing Pack for Harken Midrange Spinnaker Cars. Pack includes (60) 5/16" Torlon Balls, for use with all standard Harken Midrange Spinnaker Cars (5 1/4" long).
Spinnaker Ring Car for Harken Midrange RCB Track: Har 781: Recirculating Ball Spinnaker Car to fit Harken Midrange RCB Track. Car has cast SS Ring assembly screwed to extruded Aluminum Body. Car is 5 1/4" (132mm) long (without shackles) x 2 3/4" (70mm) wide, SS Ring is 3/8" x 1 1/4" ID, and projects 1 3/4" (maximum) from Track surface. Har 781 Car uses (60) 5/16" Torlon Balls.		R
Spinnaker Car w/ TS Pin for Harken Midrange Track: Har 1580-TS: Recirculating Ball Spinnaker Car to fit Harken Midrange RCB Track includes Forespar TS Pin & Toggle Assembly. TS Pin (1" OD x 3 5/8" long) fits all Forespar TS type Spinnaker Pole ends. Extruded Aluminum Car is 5 1/4" (132mm) long (without shackles) x 2 3/4" (70mm) wide, Toggle projects 4 5/8" (maximum) from Track surface. Har 1580 Cars use (60) 5/16" Torlon Balls.
	Car only for Harken Midrange Track & TS Pin: Har 1580: Spinnaker Car only to fit Harken Midrange Track and Forespar TS Pin & Toggle Assembly. Extruded Aluminum Car includes 1/2" vertical Pin with 1" clearance for Forespar TS Pin & Toggle Assembly. Car is 5 1/4" (132mm) long (without shackles) x 2 3/4" (70mm) wide, Pin center is 1 7/16" from Track surface. Har 1580 Cars use (60) 5/16" Torlon Balls. *As Har 1580-TS, above,* but without TS Pin & Toggle Assembly.
Spinnaker Car w/ Sparcraft Pin for Harken Midrange Track: Har 1579-SC:
Recirculating Ball Spinnaker Car to fit Harken Midrange RCB Track includes Sparcraft Bayonet Pin & Toggle Assembly. Sparcraft Bayonet Pin (7/8" OD x 4" long, beneath head) fits all Sparcraft Bayonet type Spinnaker Pole ends. Extruded Aluminum Car is 5 1/4" (132mm) long (without shackles) x 2 3/4" (70mm) wide, Toggle projects 3 3/4" (maximum) from Track surface. Har 1579 Cars use (60) 5/16" Torlon Balls.
	Car only for Harken Midrange Track & Sparcraft Pin: Har 1579: Spinnaker Car only to fit Harken Midrange Track and Sparcraft Bayonet Pin & Toggle Assembly. Extruded Aluminum Car includes 5/8" vertical Pin with 1 3/16" clearance for Sparcraft Bayonet Pin & Toggle Assembly. Car is 5 1/4" (132mm) long (without shackles) x 2 3/4" (70mm) wide, Pin center is 1 9/16" from Track surface. Har 1579 Cars use (60) 5/16" Torlon Balls. *As Har 1579-SC, above,* but without Sparcraft Bayonet Pin & Toggle Assembly.
Spinnaker Car w/ Small Bell for Harken Midrange Track: Har 1578-MBS:
Recirculating Ball Spinnaker Car to fit Harken Midrange RCB Track includes Metric Small Bell Fitting (B-130). Small Bell fitting is 51mm (2") ID, and approximately 2 9/16" (66mm) OD. Metric Small Bell Pole End Fittings, that the Bell works with, are commonly found on tubes of 50, 60, 70, and 80mm OD, and extend approximately 3 3/8" (85mm) beyond the tube end. Extruded Aluminum Car is 5 1/4" (132mm) long x 2 3/4" (70mm) wide. Har 1578 Cars use (60) 5/16" Torlon Balls.
Spinnaker Car w/ Large Bell for Harken Midrange Track: Har 1578-MBL:
Recirculating Ball Spinnaker Car to fit Harken Midrange RCB Track includes Metric Large Bell Fitting (B-120). Large Bell fitting is 66mm (2 9/16") ID, and approximately 3 1/4" (82mm) OD. Metric Large Bell Pole End Fittings, that the Bell works with, are commonly found on tubes of 80 and 100mm OD, and extend approximately 4 3/8" (110mm) beyond the tube end. Extruded Aluminum Car is 5 1/4" (132mm) long x 7/8" wide. Har 1578 Cars use (60) 5/16" Torlon Balls.
	Car only for Harken Midrange Track & Bell Fitting: Har 1578: Spinnaker Car only to fit Harken Midrange Track and Harken/Barbarossa Metric Bell Fittings. Extruded Aluminum Car includes 12mm vertical Pin with clearance for Harken/Barbarossa Metric Bell Fittings, B-120, and B-130. Car is 5 1/4" (132mm) long (without shackles) x 2 3/4" (70mm) wide, Pin center is 1 3/8" from Track surface. Har 1578 Cars use (60) 5/16" Torlon Balls. *As Har 1578-MBS,* and Har 1578-MBL, above,** but without Bell Fitting and Toggle. PC

Spinnaker Cars for Harken Big Boat Track
Harken Big Boat Recirculating Ball (RCB) Track measures 1 1/4" (32mm) across the top. Harken Big Boat Cars use 3/8" Torlon Balls.
	Replacement Balls for Harken Big Boat Spinnaker Cars: Har 782-BP:
	Replacement Ball Bearing Pack for Harken Midrange Spinnaker Cars. Pack includes (72) 3/8" Torlon Balls, for use with all standard Harken Big Boat Spinnaker Cars (7 1/4" long).
Spinnaker Car w/ TS Pin for Harken Big Boat Track: Har 784-TS: Recirculating Ball Spinnaker Car to fit Harken Big Boat RCB Track includes Forespar TS Pin & Toggle Assembly. TS Pin (1" OD x 3 5/8" long) fits all Forespar TS type Spinnaker Pole ends. Extruded Aluminum Car is 7 1/4" (185mm) long x 3 5/16" (85mm) wide, Toggle projects 4 3/4" (maximum) from Track surface. Har 784 Cars use (72) 3/8" Torlon Balls.
	Car only for Harken Big Boat Track & TS Pin: Har 784: Spinnaker Car only to fit Harken Big Boat Track and Forespar TS Pin & Toggle Assembly. Extruded Aluminum Car includes 1/2" vertical Pin with 1" clearance for Forespar TS Pin & Toggle Assembly. Car is 7 1/4" (185mm) long x 3 5/16" (85mm) wide, Pin center is 1 9/16" from Track surface. Har 784 Cars use (72) 3/8" Torlon Balls. *As Har 784-TS, above,* but without TS Pin & Toggle Assembly.
Spinnaker Car w/ Sparcraft Pin for Harken Big Boat Track: Har 783-SC:
Recirculating Ball Spinnaker Car to fit Harken Big Boat RCB Track includes Sparcraft Bayonet Pin & Toggle Assembly. Sparcraft Bayonet Pin (7/8" OD x 4" long, beneath head) fits all Sparcraft Bayonet type Spinnaker Pole ends. Extruded Aluminum Car is 7 1/4" (185mm) long x 3 5/16" (85mm) wide, Toggle projects 4" (maximum) from Track surface. Har 783 Cars use (72) 3/8" Torlon Balls.
	Car only for Harken Big Boat Track & Sparcraft Pin: Har 783: Spinnaker Car only to fit Harken Big Boat Track and Sparcraft Bayonet Pin & Toggle Assembly. Extruded Aluminum Car includes 5/8" vertical Pin with 1 3/16" clearance for Sparcraft Bayonet Pin & Toggle Assembly. Car is 7 1/4" (185mm) long x 3 5/16" (85mm) wide, Pin center is 1 7/16" from Track surface. Har 783 Cars use (72) 3/8" Torlon Balls. *As Har 783-SC, above,* but without Sparcraft Bayonet Pin & Toggle Assembly.
Spinnaker Car w/ Small Bell for Harken Big Boat Track: Har 782-MBS:
Recirculating Ball Spinnaker Car to fit Harken Big Boat RCB Track includes Metric Small Bell Fitting (B-130). Small Bell fitting is 51mm (2") ID, and approximately 2 9/16" (66mm) OD. Metric Small Bell Pole End Fittings, that the Bell works with, are commonly found on tubes of 50, 60, 70, and 80mm OD, and extend approximately 3 3/8" (85mm) beyond the tube end. Extruded Aluminum Car is 7 1/4" (185mm) long x 3 5/16" (85mm) wide. Har 782 Cars use (72) 3/8" Torlon Balls.
Spinnaker Car w/ Large Bell for Harken Big Boat Track: Har 782-MBL:
Recirculating Ball Spinnaker Car to fit Harken Big Boat RCB Track includes Metric Large Bell Fitting (B-120). Large Bell fitting is 66mm (2 9/16") ID, and approximately 3 1/4" (82mm) OD. Metric Large Bell Pole End Fittings, that the Bell works with, are commonly found on tubes of 80 and 100mm OD, and extend approximately 4 3/8" (110mm) beyond the tube end. Extruded Aluminum Car is 7 1/4" (185mm) long x 3 5/16" (85mm) wide. Har 782 Cars use (72) 3/8" Torlon Balls.
	Car only for Harken Big Boat Track & Bell Fitting: Har 782: Spinnaker Car only to fit Harken Big Boat Track and Harken/Barbarossa Metric Bell Fittings. Extruded Aluminum Car includes 12mm vertical Pin with clearance for Harken/Barbarossa Metric Bell Fittings, B-120, and B-130. Car is 7 1/4" (185mm) long x 3 5/16" (85mm) wide, Pin center is 1 1/2" from Track surface. Har 782 Cars use (72) 3/8" Torlon Balls. *As Har 782-MBS,* and Har 782-MBL, above,** but without Bell Fitting and Toggle. PC

Spinnaker Cars for Z-Spar RCB Track
Some Z-Spar Masts are equipped with a Recirculating Ball (RCB) Track for Spinnaker Cars. This special track is notable in that it is Clear Anodized and has no holes, as it is attached to the Mast by sliding it into a special groove on the front of some Z-Spar Masts. See: Spinnaker Cars for Z-Spar RCB Track.

Replacement Bayonet Pins & Toggles
Replacement Bayonet Pins and Toggles from a variety of manufacturers are available separately.
Forespar TS Pin & Toggle Ass'y for Spinnaker Car: For TS-PT: Replacement Forespar TS Pin & Toggle Assembly fits all Forespar TS type Spinnaker Pole ends, and Spinnaker Cars with a 1/2" vertical Pin and clearance for a 1" Toggle. Stainless Steel TS Pin is 1" OD x 3 5/8" long, SS Toggle is 1" high with hole for a 1/2" Pin, and is 2 3/4" between Pin centers. Suitable for use with *Har 1580,* and Har 784 Spinnaker Cars, above.
	Forespar TS Pin only: For TS-P: Replacement Forespar TS Pin only, fits all Forespar TS type Spinnaker Pole ends, and Toggles with 1/2" Pins and 1/2" ID clearance. Stainless Steel TS Pin is 1" OD x 3 5/8" long, with hole for 1/2" Pin.
	Forespar TS Toggle only: For TS-T2: Replacement Forespar Toggle only, fits Forespar TS Pins, and Spinnaker Cars with a 1/2" Pin and clearance for a 1" Toggle. Stainless Steel Toggle is 1" high with hole for a 1/2" Pin, and is 2 3/4" between Pin centers. Suitable for use with *Har 1580,* and Har 784 Spinnaker Cars, above.
*Nicro-Fico 1/2" Bayonet Pin only: NF 73-P1:* Replacement Nicro-Fico 1/2" Bayonet Pin only, fits all Nicro-Fico 1/2" Bayonet type Spinnaker Pole ends. Stainless Steel Bayonet Pin is 1/2" OD x 3 1/8" long (beneath head), head is 3/8" thick with hole for 3/8" pin. Unit is (maximum) 4 3/8" long.
*Nicro-Fico 1/2" Bayonet Pin Toggle only: NF 73-T1:* Replacement Nicro-Fico 1/2" Bayonet Pin only, fits all Nicro-Fico 1/2" Bayonet type Spinnaker Pole ends. Stainless Steel Nicro-Fico 1/2" Bayonet Pin is 1/2" OD x 3 1/8" long (beneath head), head is 3/8" thick with hole for 3/8" pin. Unit is (maximum) 4 3/8" long.
*Replacement Nicro-Fico 5/8" Bayonet Pin only: NF 73-P2:* Replacement Nicro-Fico 5/8" Bayonet Pin only, fits all Nicro-Fico 5/8" Bayonet type Spinnaker Pole ends. Stainless Steel Nicro-Fico 5/8" Bayonet Pin is 5/8" OD x 3 1/8" long (beneath head), head is 7/16" thick with hole for 3/8" pin. Unit is (maximum) 4 5/8" long.
Sparcraft Pin & Toggle Ass'y for Spinnaker Car: SC 73-12PT:
Replacement Sparcraft Bayonet Pin & Toggle Assembly fits all Sparcraft Bayonet type Spinnaker Pole ends, and Spinnaker Cars with a 5/8" vertical Pin and clearance for a 1 3/16" Toggle. Stainless Steel Sparcraft Bayonet Pin is 7/8" OD x 4" long (beneath head), standard SS Toggle (Type 1) is 1 3/16" high with hole for a 5/8" Pin. Suitable for use with *Har 1579,* and *Har 783* Spinnaker Cars, above.
	*Sparcraft Bayonet Pin only: SC 73-13P:* Replacement Sparcraft Bayonet Pin only, fits all Sparcraft Bayonet type Spinnaker Pole ends. Stainless Steel Sparcraft Bayonet Pin is 7/8" OD x 4" long (beneath head), head is 9/16" thick with hole for 1/2" pin. Unit is (maximum) 5 3/4" long.
	Sparcraft Type 1 Toggle only: SC 73-12T1: Replacement Sparcraft Toggle (Type 1) fits Sparcraft Bayonet Pin and Spinnaker Cars with a 5/8" vertical Pin and clearance for a 1 3/16" Toggle. Stainless Steel Toggle is 1 3/16" high x 1 3/8" wide with holes for 5/8" (Vertical) and 1/2" (Horizontal) Pins, and measures 1 5/8" between Pin centers. Horizontal (1/2") Pin is included. Suitable for use with *Har 1579,* and Har 783 Spinnaker Cars, above.
Z-Spar Spinnaker Pin & Toggle Ass'y: Z-73-ZPT: Replacement Z-Spar Bayonet Pin & Toggle Assembly fits all Z-Spar Pin type Spinnaker Pole ends, and Spinnaker Cars with a 12mm vertical Pin and clearance for a 1 5/16" (34mm) Toggle. Z-Spar Pin is 16mm x 100mm (4") long tip to Pin center, Aluminum Toggle is 1 5/16" (34mm) high with hole for a 12mm Pin.

Replacement Metric Bell Fittings
Replacement Metric Bell Fittings are available separately.
Metric Small Bell & Toggle only: Har B-130: Replacement Metric Small Bell and Toggle Assembly for use with spinnaker poles using Francespar or Barbarossa inboard Small Bell Pole Ends. Small Bell fitting is 51mm (2") ID, and approximately 2 9/16" (66mm) OD, Toggle has hole for 12mm Pin and is 1 3/8" (34mm) high. Metric Small Bell Pole End fittings, that the Bell works with, are commonly found on tubes of 50, 60, 70, and 80mm OD, and extend approximately 3 3/8" (85mm) beyond the tube end. Suitable for use with *Har 1578,* and Har 782 Spinnaker Cars, above.
Metric Large Bell & Toggle only: Har B-120: Replacement Metric Large Bell and Toggle Assembly for use with spinnaker poles using Francespar or Barbarossa inboard Large Bell Pole Ends. Large Bell fitting is 51mm (2") ID, and approximately 2 9/16" (66mm) OD, Toggle has hole for 12mm Pin and is 1 3/8" (34mm) high. Metric Large Bell Pole End fittings, that the Bell works with, are commonly found on tubes of 80 and 100mm OD, and extend approximately 4 3/8" (110mm) beyond the tube end. Suitable for use with *Har 1578,* and Har 782 Spinnaker Cars, above.

Spars, Rigging, and Hardware for Sailboats