Kenyon 1/2" OD Spreader Section

*1/2" OD Spreader Tube: K-SPR4XCA-____:* 1/2" Outside Diameter (OD) Round Spreader Tube is used in a variety of Applications on dinghies and small yachts as Spreaders and for use as Jumper and Diamond stay Struts. Stocked in a clear anodized finish it is available in 2', 4', and 6' lengths, or can be cut to shorter lengths. To order: specify length.

1/2" OD Round Spreader Assemblies & Parts
1/2" OD Round Spreader Assemblies come in 2 different styles, to fit different Spreader Base configurations. The difference between the 2 styles is the distance between the inboard end of the Spreader and its' attachment hole. Because of the variety of different Kenyon Spreader Bases you must measure this dimension to find the right Replacement Spreader Assembly to fit your Mast. To order 1/2" OD Round Replacement Spreaders you must know the Overall Length of the Spreader and the distance between the inboard end of the Spreader and its' 1/4" attachment hole.
*1/2" OD Standard Spreader Assembly: K-SPR4AP-____:* Standard 1/2" OD Round Spreader Assembly attaches to mast Bracket with a 1/4" hole 3/8" from the inboard end. Outboard end has integral slot for shroud up to 1/8" diameter, and holes for seizing wire (included). For use with K-365 and K-365T Spreader Bases. A variety of common lengths are stocked, other lengths are available on special order. 1/2" OD Round Spreaders are only sold in pairs. Standard Lengths: 13", 18", 21 1/4", 24". To order: specify maximum length.
*1/2" OD Spreader Assembly: K-SPR4ALP-____:* 1/2" OD Round Spreader Assembly attaches to mast Bracket with a 1/4" hole 1 5/8" from the inboard end. Outboard end has integral slot for shroud up to 1/8" diameter, and holes for seizing wire (included). For use with *K-366* Spreader Bases. A variety of common lengths are stocked, other lengths are available on special order. 1/2" OD Round Spreaders are only sold in pairs. Standard Lengths: 14 1/2", 17 3/4", 18 1/2", 20 1/4", 21 1/4", 24". To order: specify maximum length, OR* consider using the heavier *K-1118AP* Spreaders which also work with the *K-366* Spreader Base.
Tip Adjuster for 1/2" OD Jumper and Diamond Struts: K-40449: Aluminum threaded adjuster is used to adjust jumper and diamond stay tension without using a turnbuckle. SS nut (included) seats against strut outboard end and is turned to push stay further out. Adjuster is suitable for tubular struts with a 1/2" (or larger) OD and a 3/8" ID. Adjuster stud is 3/8" diameter x 3 1/2" long and features cross-hole for seizing wire. Allows for over 1 1/2" of adjustment.

Spreader Bases for 1/2" OD Round Spreaders
Listed below are Spreader Bases commonly used with 1/2" OD Round Spreaders.
*Aluminum Spreader Bracket Assembly: K-365:* Cast Aluminum Spreader Bracket has curved base to fit Mast Section and incorporates tabs to fit 1/2" OD Standard Spreaders. Spreaders are attached with a 1/4" clevis pin (included), and are free to swing fore and aft. Bracket is 2 3/8" high x 7/8" wide and projects 1 1/8" out from the side of the mast when mounted. Bracket attaches to the mast with (3) 3/16" (#10) fasteners. Used with *K-SPR4AP* Spreaders, above.
*Triangular Aluminum Spreader Bracket Assembly: K-365T:* Cast Aluminum Spreader Bracket has wide triangular base curved to fit Mast Section and incorporates tabs to fit 1/2" OD Standard Spreaders. Spreaders are attached with a 1/4" clevis pin (included), and are free to swing fore and aft. Bracket is 2 3/8" high x 1 1/8" wide and projects 1 1/8" out from the side of the mast when mounted. Bracket attaches to the mast with (3) 3/16" (#10) fasteners. Similar to *K-365, above, but with wider base for greater support. Used with K-SPR4AP* Spreaders, above.

Kenyon Spars 1/2" Round Spreader Section Measurements: 0.5" OD x .384" ID (1/2" OD x 3/8" ID) Wall Thickness: .058" Weight/ft.: .098 lbs. Moments of inertia: Ixx = Alloy: 6063-T6 Stock Length: 6' Common Boat usage: Dinghies & Daysailers

1/2" OD Round Spreader Tube

Spars, Rigging, and Hardware for Sailboats