Isomat NG70 Mast

NG2 Masthead Sheave: NG2-3: Factory standard Acetyl Sheave is 85mm (3 3/8") x 15mm (5/8") wide x 22mm (7/8") ID.
NG2 Masthead Sheave - Aluminum: NG2-3A: Anodized Aluminum Sheave is 85mm (3 3/8") x 15mm (5/8") wide x 22mm (7/8") ID, and is much sturdier than the plastic version.
*NG2 Short Masthead Sheave Axle: NG2-6S:* Short SS ’Drop-in’ Tubular Masthead Sheave Axle is 22mm (7/8") OD x 46mm (1 3/4") long. Hollow Axle fits in Aft side of NG2 Masthead and supports 2 Main Halyard Sheaves (NG2-3 or NG2-3A).
*NG2 Long Masthead Sheave Axle: NG2-6L:* Long SS ’Drop-in’ Tubular Masthead Sheave Axle is 22mm (7/8") OD x 81mm (3 1/4") long. Hollow Axle fits in Forward side of NG2 Masthead and supports 4 Jib/Spinnaker Halyard Sheaves (*NG2-3* or *NG2-3A*).
*NG2 Masthead Clevis Pin: NG2-6P:* SS Clevis Pin is used in NG2 Masthead for attachment of topping lift, lazy jacks, or other items. This item is not standard on all masts and your Masthead may not have a hole drilled for this Pin, but, if not drilled, hole position is marked by an indent. Masthead can be easily drilled to add this item if required. Clevis Pin is 8mm (5/16") diameter with a 52mm (2 1/16") grip length. CPM8-52

NG-70 Mast – Jib Boxes for Fractional Rigs
*NG2 Jib Box Assembly with Toggle (12mm Pin): NG2-32A:* *NG2 Jib Box Assembly with Toggle (14mm Pin): NG2-34A:* NG2 Jib Box Assembly with Toggle (16mm Pin): NG2-36A: Cast aluminum Jib Box and Forestay Toggle Assembly is designed to be welded in Mast Section. Unit provides a single sheave for an internal Jib halyard up to 5/8" diameter and a secure attachment point for Forestays up to 3/8" (10mm) diameter. Assembly uses an 85mm (3 3/8") Acetyl Sheave (NG2-18) on a 16mm Axle, (NG2-6B). Toggle mounts on removable 19mm Clevis Pin which can be used to mount optional Spinnaker halyard Spectacle Assembly (*NG2-39S*), below. Stainless Steel Toggle with Pin (in various pin sizes) is included. Other Pin sizes (1/2" - 5/8") are available, please specify.
	NG2 Jib Box Sheave: NG2-18: Acetyl Sheave is 85mm (3 3/8") OD x 20mm (3/4") wide x 16mm (5/8") ID.
	NG2 Jib Box Sheave Axle: NG2-6B: SS ’Drop-in’ Sheave Axle pin is 16mm (5/8") diameter x 29.5mm (1 5/32") long.
	*NG2 Jib Box Forestay Toggle (12mm Pin): NG2-32TA:* *NG2 Jib Box Forestay Toggle (14mm Pin): NG2-34TA:* *NG2 Jib Box Forestay Toggle (16mm Pin): NG2-36TA:* Stainless Steel Toggle for use with NG2 Cast Jib Box. Toggle rides on 19mm Pin in casting, lower Clevis pin (in various sizes) is included. Other Pin sizes (1/2" - 5/8") are available, please specify.
	*NG2 Jib Box Toggle Attachment Pin: NG2-38P:* SS Clevis Pin is used in NG2 Cast Jib Box for attachment of Forestay Toggle. Clevis Pin is 19mm (3/4") diameter with a 52mm (2 1/16") grip length. Single Pin is also used for attachment of optional Spinnaker halyard Spectacle Assembly (NG2-39S), below. CPM19-52
	NG2 Jib Box Spinnaker Spectacles: NG2-39S: Optional SS Spectacle Assembly for NG2 Cast Jib Box allows for two (2) Spinnaker halyards and mounts easily on Jib Box Toggle Pin. Cast Stainless 'eyes' are smoothly faired to minimize chafe on halyards up to 1/2" diameter. Spinnaker halyards exit mast through staggered Exit Blocks mounted several feet above Jib Box Assembly and go straight down through Spectacle 'eyes' and forward.

NG-70 Mast – Exit Blocks Several varieties of Exit Blocks are used on the NG-70 Mast Section, See Isomat Exit Blocks.

NG-70 Mast – Spreaders The NG-70 Mast Section is commonly used with Several different sizes of Spreaders. Standard Spreader Bases are listed below, for Spreaders, Spreader Parts, and other Spreader Bases, See Isomat Spreaders and Components.

NG-70 Mast – Spreader Bases
Spreader Base for BF3 Spreader - Port: BF3-36P: Spreader Base for BF3 Spreader - Starboard: BF3-36S: Unique spreader base design incorporates (2) sockets for use with stemballs on lower and intermediate shrouds. Cast aluminum bases are welded to the mast and accommodate a variety of spreader angles depending on how the inboard spreader end is cut. BF-3 Spreader is attached with (1) 8mm clevis pin which goes through a plastic bushing to allow for some shock loading. New Bases have hole for 12mm (7/16") OD Spreader Bushing, BF3-31. Base measures 4 1/2" high x (maximum) 4 1/4" long, and projects 3 3/4" out from the Mast. For use with NG-31 through NG-70 Mast Sections. Please specify Mast Section and port or starboard when ordering. For Spreaders and Spreader Parts, See Isomat Spreaders and Components.
Bolt-on Spreader Base for BF3 Spreader - Port: BF3-37P: Bolt-on Spreader Base for BF3 Spreader - Starboard: BF3-37S: Identical to *BF3-36, above, but attaches to mast with (1) 10mm (3/8") bolt, and (4) 6mm (1/4") rivets. Not as strong as when welded, but especially suited for replacement in the field. Please specify Mast Section and port or starboard when ordering. For Spreaders and Spreader Parts,* See BF-3 Spreaders and Components.
<Spreader Base for BF4 Spreader - Port: BF4-35P: Spreader Base for BF4 Spreader - Starboard: BF4-35S: Unique spreader base design incorporates (2) sockets for use with stemballs on lower and intermediate shrouds. Cast aluminum bases are welded to the mast and accommodate a variety of spreader angles depending on how the inboard spreader end is cut. BF-4 Spreader is attached with (1) clevis pin that goes through a bushing to allow for some shock loading. Bases have hole for 21mm (13/16") OD Spreader Bushing. Base measures 5 1/8" high (maximum) x 4 7/8" long, and projects 5" out from the Mast. For use with NG-46 and larger Mast sections. Please specify Mast Section and port or starboard when ordering. For Spreaders and Spreader Parts, See Isomat Spreaders and Components.
Spreader Base for BF5 Spreader - Port: BF5-35P: Spreader Base for BF5 Spreader - Starboard: BF5-35S: Unique spreader base design incorporates (2) sockets for use with stemballs on lower and intermediate shrouds. Cast aluminum bases are welded to the mast and accommodate a variety of spreader angles depending on how the inboard spreader end is cut. BF-5 Spreader is attached with (1) 12mm clevis pin that goes through a plastic bushing to allow for some shock loading. New Bases have hole for 21mm (13/16") OD Spreader Bushing, BF5-31. Base measures 5 1/2" high (maximum) x 6 3/8" long, and projects 5 1/4" out from the Mast. For use with NG-70 and larger Mast sections. Please specify Mast Section and port or starboard when ordering. For Spreaders and Spreader Parts, See Isomat Spreaders and Components.

NG-70 Mast – Spinnaker Cars Several varieties of Spinnaker Cars are used on the NG-70 Mast Section, See Isomat Spinnaker Cars.

NG-70 Mast – Exit Plates Several varieties of Exit Plates are used on the NG-70 Mast Section, See Isomat Exit Plates.

NG-70 Mast – Cleats Several sizes of Cleats are used on the NG-70 Mast Section, See Isomat Cleats.

NG-70 Mast – Mainsail Gates
NG2 Mainsail Gate & Screw Kit: NG2-9K: Cast aluminum Mainsail Gate fits NG-60 through NG-105 Mast Sections. Gate has horizontal slot for Thumbscrew (*NGA-10); Gate is ‘opened’ by loosening Thumbscrew and sliding gate away from Mainsail track. Kit includes Gate casting, NG2-9, and SS Thumbscrew, NGA-10.*
	NG2 Mainsail Gate: NG2-9: Cast aluminum Mainsail Gate fits NG-60 through NG-105 Mast Sections. Gate casting is 2 3/8" (60mm) high x 1 7/16" (36mm) wide, with 1/4" (7mm) deep lip. Part is labeled #157007.
	NG2 Mainsail Gate Screw: NGA-10: SS Thumbscrew is 4mm diameter with 5/8" (15mm) long thread and has serrated plastic head.
Autoreef Fairlead
*Autoreef Fairlead: NGA-65:* SS Autoreef Fairlead is mounted on either side of mast above gooseneck bracket. Acts as fairlead for reef line and stop for sail when reefed with AutoReef (single line) reefing system. Flattened SS ring is welded to diamond shaped SS plate. Ring is 32mm (1 1/4") OD x 16mm (5/8") ID, plate is 65mm (5/8") high x 40mm (1 5/8") wide and is fastened with eight (4) 1/4" (6mm) rivets.

NG-70 Mast - Gooseneck Brackets and Hardware
*NG2 Gooseneck Bracket: NG2-11:* Cast aluminum Gooseneck Mast Bracket for use with NB-32, NB-40, and NB-55 new-style Gooseneck Assemblies. Bracket fits NG-51 through NG-86 Mast Sections and is fastened with eight (8) 1/4" (6mm) rivets. Bracket has 22mm (7/8") hole at top and 8mm (5/16") hole on bottom side, for use with any of the NB2-1 Vertical Gooseneck Toggle Pins. For Gooseneck Parts not listed below, See NB-32, NB-40, or NB-55 Boom Section.
NB-2 Vertical Gooseneck Toggle Assembly w/ Reef Hooks: NB2-1A: Vertical Gooseneck Toggle Pin Assembly with Tack Shackle and Reef Hooks is used to attach the NB2 Gooseneck to Isomat Gooseneck Mast Bracket (NG2-11). SS Toggle Pin has 2 integral Reef Hooks and is 22mm (7/8") diameter with an 8mm (5/16") threaded stud on the bottom, with washer and SS Locknut. Assembly includes Tack Shackle (NB2-2) and Horizontal Gooseneck Pin (NB2-3).
NB-2 Vertical Gooseneck Toggle Pin w/ Reef Hooks: NB2-1: Vertical Gooseneck Toggle Pin with Reef Hooks includes washer and SS Locknut. As NB2-1A, above, but without Tack Shackle and Horizontal Gooseneck Pin. SS Toggle Pin has 2 integral Reef Hooks and is 22mm (7/8") diameter with an 8mm (5/16") threaded stud on the bottom, and has (2) 10mm (3/8") cross-holes for Tack Shackle and Horizontal Gooseneck Pin.
	NB-2 Tack Shackle: NB2-2: SS Tack Shackle fits through hole in top of NG2 Vertical Gooseneck Toggle Pins. Shackle has 8mm (5/16") pin.
	NB-2 Horizontal Gooseneck Pin: NB2-3: Clevis Pin is 10mm (3/8") dia. x 49mm (2") long. Used to attach the NB2 Gooseneck to Isomat Vertical Gooseneck Toggle Pin (*NB2-1*).
NB-2 Vertical Gooseneck Toggle Assembly: NB2-1ARA: Vertical Gooseneck Toggle Pin Assembly is used to attach the NB2 Gooseneck to Isomat Gooseneck Mast Bracket (NG2-11). For use with AutoReef Systems not requiring Reef hooks. SS Toggle Pin is 22mm (7/8") diameter with an 8mm (5/16") threaded stud on the bottom, with washer and SS Locknut. Assembly includes Tack Shackle (*NB2-2) and Horizontal Gooseneck Pin (NB2-3*).
	NB-2 Vertical Gooseneck Toggle Pin - AR: NB2-1AR: Vertical Gooseneck Toggle Pin includes washer and SS Locknut. As NB2-1ARA, above, but without Tack Shackle and Horizontal Gooseneck Pin. For use with AutoReef Systems not requiring Reef hooks. SS Toggle Pin is 22mm (7/8") diameter with an 8mm (5/16") threaded stud on the bottom, and has (2) 10mm (3/8") cross-holes for Tack Shackle and Horizontal Gooseneck Pin.
NB-2 Old-Style Vertical Gooseneck Toggle Pin: NB2-1XP: Vertical Gooseneck Toggle Pin Assembly is used to attach the NB2 Gooseneck to Isomat Gooseneck Mast Bracket (NG2-11). Has 10mm (3/8") cross pin at top for using the Old-Style Reef Hook/Tack Assembly (NB2-5X). SS Toggle Pin is 22mm (7/8") diameter with an 8mm (5/16") threaded stud on the bottom, has 10mm (3/8") cross-hole for Horizontal Gooseneck Pin (NB2-3), and includes washer and SS Locknut.
	NB-2 Old-Style Reef Hook/Tack Attachment: NB2-5X: Old-Style formed combination SS Reef Hook and Tack anchor is passed through the tack grommet in sail and clipped over horizontal cross pin in top of special 22mm gooseneck pin, *NG2-1P.* Formed from heavy 10mm (3/8") SS rod, unit measures a maximum of 4" (100mm) high x 3 1/2" (90mm) wide.
NG2 Old-Style Gooseneck Bracket: NG2-11X: Old-Style Cast aluminum Gooseneck Mast Bracket fits NG-51 through NG-86 Mast Sections, for use with NB-32, NB-40, and NB-55 old-style Gooseneck Assemblies. Bracket is 3 7/8" (98mm) high x 3 1/2" (90mm) wide, and is fastened with eight (8) 1/4" (6mm) rivets. Bracket has hole for 10mm (3/8") Vertical Pin, NB2-1XA, used with SS Gooseneck Toggle NB2-2XA. For parts associated with this Gooseneck Bracket, See NB-32, NB-40, or NB-55 Old-Style Gooseneck Assemblies.

NG-70 Mast – Winch Pads
NG-70 Side Winch Pad - Clear Anodized: NG70-20: NG-70 Side Winch Pad - Black: NG70-20B: Formed aluminum Bracket fits either side of NG-70 Mast Section. Winch mounting surface on Bracket is 5 1/2" (140mm) high x 5 1/4" (132mm) wide. Anodized Bracket is 3/16" (5mm) thick and fastens to Mast with eight (8) 1/4" (6mm) rivets. 67,60
NG-70 Aft Winch Pad - Clear Anodized: NG70-21: NG-70 Aft Winch Pad - Black: NG70-21B: Formed aluminum Bracket fits aft side of NG-70 Mast Section. Designed to mount under the Boom for use with a Reef line winch. Winch mounting surface on Bracket is 5 1/8" (130mm) high x 4 5/8" (118mm) and angles aft approximately 12 degrees to align Winch with Outhaul or Reef lines exiting from Boom. Anodized Bracket fastens to Mast with eight (8) 1/4" (6mm) rivets. 60,0

NG-70 Mast - Vang Brackets and Hardware Brackets are available with Toggles to fit any type of Vang. Isomat Masts were often supplied with an Isovang solid Vang as standard equipment, they are also commonly added to boats originally supplied without one. See: Isomat Isovangs.
NG2 Vang Bracket: NG2-12: Cast aluminum Vang Bracket fits NG-51 through NG-86 Mast Sections. Bracket is 4 3/4" (120mm) high x 3 1/2" (90mm) wide, and is fastened with eight (8) 1/4" (6mm) rivets. Bracket has 22mm (7/8") hole at top and 14mm (9/16") hole on bottom side, for use with the NG2-14A Vertical Vang Toggle Pin Assembly, and any of the NG2 Vang Toggles listed below. MS
NG2 Vang Toggle Pin Assembly: NG2-14A: Assembly converts NG2 Vang Bracket, NG2-12, for use with any of the NG2 Vang Toggles listed below. Includes Vang Toggle Pin (*NG2-14), NG2 Vang Bushing (NG2-13*), and SS Cotter Ring.
	NG2 Vang Toggle Pin: NG2-14: SS Clevis Pin is 14mm (9/16") diameter with a 125mm (5") grip length, and has 8mm (5/16") hole for Cotter Ring or Block attachment. Fits vertically in NG2-12 Vang Bracket.
	NG2 Vang Bushing: NG2-13: SS Bushing is used in upper hole of NG2-12 Vang Bracket to adapt it for use with Vang Toggle Pin (NG2-14). Bushing is 22mm (7/8") OD x 14mm (9/16") ID x 16mm (5/8") long.
*NG2 Vang Bracket Assembly w/ 5/8" Toggle: NG2-17A:* Complete NG2 Vang Bracket Assembly with Toggle for Vang with 5/8" Pin. Assembly consists of Vang Bracket (NG2-12), Vang Toggle Pin Assembly (NG2-14A), and NG2-17 Vang Toggle with 5/8" hole. Assembly is fastened to Mast with eight (8) 1/4" (6mm) rivets or screws.
	*NG2 SS Vang Toggle w/ 5/8" hole: NG2-17:* SS Welded Vang Toggle Fits NG2-12 Vang Bracket. SS tube is 2 5/8" (67mm) long and is drilled for 14mm Vertical Pin, *NG2-14.* Welded SS Tab is 5.5mm (7/32") thick and projects 2 1/2" (65mm) out from tube. Tab has 5/8" (16mm) hole for attachment of Vang.
*NG2 Vang Bracket Assembly w/ 7/8" Toggle: NG2-19A:* Complete NG2 Vang Bracket Assembly with Toggle for Vang with 22mm (7/8") Pin. Assembly consists of Vang Bracket (NG2-12), Vang Toggle Pin Assembly (NG2-14A), and NG2-19 Vang Toggle with 22mm (7/8") hole. Assembly is fastened to Mast with eight (8) 1/4" (6mm) rivets or screws. For use with the NG2 Isovang. Also recommended for use with Soft (block and tackle) Vangs, as the large hole will accommodate any shackle.
	*NG2 SS Vang Toggle w/ 7/8" hole: NG2-19:* SS Welded Vang Toggle Fits NG2-12 Vang Bracket. SS tube is 2 5/8" (67mm) long and is drilled for 14mm Vertical Pin, *NG2-14.* Welded SS Tab is 5.5mm (7/32") thick and projects 4" (100mm) out from tube. Tab has 22mm (7/8") hole for attachment of NG2 Isovang.

NG-70 Mast - Welded Mast Base Exit Boxes Some Isomat Masts have Welded Exit Boxes at the base of the mast for leading internal halyards out of the Mast at Deck level, rather than higher on the mast using standard Exit Plates. Halyards exit the Mast angled aft, toward the cockpit, eliminating the need for any additional hardware at the base of the Mast. Welded Exit Boxes are especially common on Cruising Yachts. The NG-70 Mast Section would normally use NG2 Welded Exit Boxes, See Welded Mast Base Exit Boxes.

NG-70 Mast - Deck Collars, Mast Boots and Hardware
NG-70 Mast Boot: NG70-15B: Heavy molded Black Rubber Boot for use with NG-70 and larger NG Mast sections. Lower side of Boot fits over Deck Collar, upper side fits Mast section. 17,105
NG-70 White Mast Boot - Special for 7-Bail Deck Collar: NG70-15B-10:
Deluxe Hard molded White PVC Mast Boot to fit NG-70 Mast Section and 7-Bail Deck Collar, NG70-10, below. White PVC Mast Boot is 10 1/2" long x 2 1/2" high. As used on O'Day 39.
NG-70 Mast Boot Clamp: NG70-16M: All Stainless Steel Clamp for use with Mast Boot on NG-70 Mast.
NG-70 Deck Collar Boot Clamp: NG70-16D: All Stainless Steel Clamp is suitable for use with Mast Boots on all NG-70 Deck Collars.
*Mast Collar Wedge – Small Rubber: NGA-18:* Heavy Extruded Rubber Wedge for use with Isomat and other Masts. Small stepped Rubber Wedge is used to support the mast as it passes through the Deck Collar. Wedge is 2 3/4" (70mm) long x 1 1/8" (28mm) wide, and is 15/16" (24mm) thick at the top tapering to 3/8" (10mm) thick at the bottom.
*Mast Collar Wedge – Large Rubber: NGA-19:* Heavy Extruded Rubber Wedge for use with Isomat and other Masts. Large stepped Rubber Wedge is used to support the mast as it passes through the Deck Collar. Wedge is 2 3/4" (70mm) long x 1 1/8" (28mm) wide, and is 1 3/16" (30mm) thick at the top tapering to 11/16" (18mm) thick at the bottom.
*Mast Collar Wedge – Large Wood: NGA-19W:* Wedge for use with Isomat and other Masts. Large stepped Wood Wedge is used to support the mast as it passes through the Deck Collar. African mahogany Wedge is 2 3/4" (70mm) long x 1 1/8" (28mm) wide, and is 1 5/16" (33mm) thick at the top tapering to 3/4" (20mm) thick at the bottom.
NG-70 Deck Collar – 7 Bail Type: NG70-10: Cast Aluminum Deck Collar for use with NG-70 Mast Section. Deck Collar has provisions for 7 bails ((1) NG2-20, aft, and (6) NG1-20, on the sides), for attachment of a soft Boom Vang and up to 6 standard blocks. Cast Deck Collar is 12 3/8" (313mm) long x 9 1/2" (243mm) wide, and fastens to deck with (6) 1/4" (6mm) screws. Maximum inside dimensions 9 1/2" x 6 3/16". Bcirc. 27 7/8". 013,60
NG1 Deck Collar Bail: NG1-20: SS Formed Bail is used for attachment of blocks and lines. Fits in integral slots in sides of NG70 and smaller Deck Collars. Bails are installed from underside of Deck Collar Casting, Deck Collar must be removed to install Bails. Bail is made from 8mm (5/16") rod, and is 2 1/16" (53mm) long x (maximum) 1" (25mm) high.
NG2 Deck Collar Bail: NG2-20: SS Formed Bail is used for attachment of Boom Vang. Fits in integral slot in aft side of Deck Collar. Bail is installed from underside of Deck Collar Casting, Deck Collar must be removed to install Bail. Bail is made from 10mm (3/8") rod, and is 2 3/4" (70mm) long x (maximum) 1 15/16" (50mm) high.
NG-70 Deck Collar – New Style: NG70-12: Cast Aluminum Deck Collar for use with NG-70 Mast Section. Deck Collar has provisions for 14 new-style Mast Base Turning Blocks and a SS Bail, NG2-20, for attachment of a soft Boom Vang. Nut slots on underside of casting and 12mm holes allow for attachment of NG2 threaded Block Studs, and/or Mast Base Turning Blocks, NGA-40 or NGA-41, without unfastening Deck Collar. Includes four (4) provisions for deck tie-down turnbuckles, and slots for (2) NGA-18 and (4) NGA-19 Mast Wedges. Cast Deck Collar is 14 1/8" (360mm) long x 11 1/4" (285mm) wide, and fastens to deck with (6) 3/8" (10mm) screws. Maximum inside dimensions 9 13/16" x 7 11/16". Bcirc. 32 1/2". 020,80
Deck Tie-Down Bracket: PP M2259: Deck Tie-Down Bracket is attached to the mast, for use with a tie rod to hold the deck in place under rigged loads. Black epoxy-coated cast aluminum Bracket has curved mounting base to suit a wide variety of mast sections. Mounting base is 4" long x 2" wide, original unit was attached to the mast with (2) 5/16" screws on 2 1/2" vertical centers. New, improved version has same hole spacing as original, but can be attached to the mast with up to (4) 5/16" screws. Bracket projects 2" from mast surface and has a hole for a 3/8" tie rod 1 5/16" from mast. As used on a variety of Pearson Yachts, including Pearson 36-2.

NG-70 Mast - Mast Steps
NG-70 Mast Step – 5 Bail Type: NG70-2: Cast Aluminum Mast Step for use with NG-70 Mast Section. Mast Step has provisions for 5 bails (*NG2-20*), for attachment of a soft Boom Vang and up to 4 standard blocks. Cast Mast Step is 10 5/8" (270mm) long x 8" (203mm) wide, and fastens to deck or keel with (4) 5/16" (8mm) FH Screws on 9" (230mm) (fore & aft) x 6 3/8" (160mm) (athwartships) centers. 134
NG-70 Mast Step – Block Stud Type: NG70-4: Cast Aluminum Mast Step for use with NG-70 Mast Section. Mast Step has provisions for 10 clevis-pin like 12mm Block Studs, NG2-20PS, for attachment of Blocks with Bolt for Block Studs for leading halyards aft, and a bail (*NG2-20*), for attachment of a soft Boom Vang. Block Studs insert in recessed 12mm holes from underside of casting and have a 6mm (1/4") hole for block attachment. Mast Step must be removed to install Block Studs. Cast Mast Step is (maximum) 11" (280mm) long x 9 1/2" (240mm) wide, and fastens to deck or keel with (6) 5/16" (8mm) FH Screws. 177FR,60pic8
	NG2 Mast Step Block Stud: NG2-20PS: SS Clevis Pin-shaped Block Stud is used for attachment of shackle or block to lead halyards aft. Fits in integral recessed hole in NG60-4, and NG70-4 Mast Steps. Block Stud is installed from underside of Mast Step Casting, Mast Step must be removed to install Block Studs. Small head Block Stud is 12mm diameter x 45mm (1 3/4") long (maximum), with a 30mm (1 3/16") grip length and a 6mm (1/4") hole for shackle pin or Block bolt.
NG-70 Mast Step – New Style: NG70-5: Cast Aluminum Mast Step for use with NG-70 Mast Section. Mast Step has provisions for 8 new-style Mast Base Turning Blocks and a SS Bail, NG2-20, for attachment of a soft Boom Vang. Nut slots on underside of casting and 12mm holes allow for attachment of Mast Base Turning Blocks, NGA-40 or *NGA-41*, without unfastening Mast Step. Cast Mast Step is 11 1/8" (285mm) long x (maximum) 8 3/4" (220mm) wide, and fastens to deck or keel with (4) 1/4" (6mm) FH Screws on 8 7/8" (225mm) (fore & aft) x 4 3/4" (120mm) (athwartships) centers. 180,60
NG-70 Mast Step – Special: NG70-6: Cast Aluminum Mast Step for use with NG-70 Mast Section. Cast Mast Step is 13 3/8" (340mm) long x 10 3/8" (265mm) wide, and fastens to deck or keel with (4) 5/16" (8mm) FH Screws on 8 1/2" (215mm) (fore & aft) x 6 1/4" (160mm) (athwartships) centers. As used on Beneteau Oceanis 400. 182,F580,F560E
NG-70 Mast Step – Special Keel: NG70-1SK: Special welded Aluminum Mast Step for use with Keel stepped NG-70 Mast Section. Clear Anodized Mast Step has (2) two slots on each end that are 1/2" wide x 2 1/2" long on 4 1/2" (athwartships) centers. Mast Step is 15" (380mm) long x 6 1/2" (165mm) wide x 1/4" (6mm) thick, and fastens to keel with (4) Hex head bolts. As used on Pearson 422 and others. PXmc
NG2 Mast Step Bail: NG2-20: SS Formed Bail is used for attachment of Boom Vang or/and standard blocks for leading halyards aft. Fits in integral slots in NG46 and larger Mast Steps. Bail is installed from underside of Mast Step Casting, Mast Step must be removed to install Bail(s). Bail is made from 10mm (3/8") rod, and is 2 3/4" (70mm) long x (maximum) 1 15/16" (50mm) high.
NG-70 Mast Base Halyard Turning Blocks A variety of Mast Base Turning Blocks and Block Studs are used with the NG-70 Mast Steps and Deck Collars, See Isomat Mast Base Turning Blocks.

NG-70 Mast Components
Masthead Parts Jib Boxes Exit Blocks Spreaders Spreader Bases Spinnaker Cars Exit Plates Cleats	Mainsail Gates Gooseneck Brackets Winch Pads Vang Brackets and Hardware Mast Base Halyard Exit Boxes Deck Collars, Mast Boots and Hardware Mast Steps Mast Base Halyard Turning Blocks


NG-70 Mast – Masthead Parts NG2 Mastheads are cast from high-strength Aluminum alloy, and are welded into the mast section. Isomat NG2 Mastheads are easily identified by having 4 sheaves (or provision for 4 sheaves) side by side, on the forward side. For Details, See: NG2 Masthead Assembly.
NG2 Masthead Cover Plate: NG2-1: Cast aluminum Masthead Cover Plate for NG2 standard Masthead. Masthead Cover Plate also provides level surface for mounting Anchor light and has holes and slots for exiting other electrical wires. Unit is 10 1/4" (260mm) long (maximum) x 7 1/8" (180mm) wide, and is fastened with two (2) 6mm screws, NG2-1S, that thread into tapped holes in Masthead.
NG2 Masthead Spinnaker Crane: NG2-2: Heavy SS Masthead Spinnaker Crane is designed to attach to standard Isomat NG2 Masthead. Crane allows for off-center attachment of one or two standard swivel blocks for external spinnaker halyards, See Spinnaker Halyard Blocks. This method of running spinnaker halyards has less friction and eliminates the chafe on halyards that is inherent in the standard internal halyard design – it is the only choice for long-distance racing or cruising. Halyards can be led internally; running from the swivel block to an entrance 5-8 feet down from the masthead, but this method does add a potential chafe spot. Attaches with (4) 5/16" (8mm) bolts and locknuts. SS Plate is (maximum) 4" long x 5 3/8" wide x 1/4" thick, and projects 1 3/8" forward of the masthead. Easily positioned on the masthead, mounting requires drilling (4) 5/16" holes in the masthead. Unit comes complete with fasteners.

Spars, Rigging, and Hardware for Sailboats