 |
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Aluminum Stanchion Bases |
|
|
Spars, Rigging, and Hardware for SailboatsRig-Rite, Inc. |
Aluminum Stanchion Bases |
|
| Aluminum Stanchion Bases |
| Cast Aluminum Stanchion Bases have been produced in a variety
of configurations, by many different Boat Builders and Hardware manufacturers. If a
Stanchion Base you require is not listed here, please contact us with a sketch and
complete dimensions, including base footprint, hole spacing, and angle. All Stanchion Bases listed here are for use with 1" (25.4mm) Stanchions, unless otherwise noted. The one C&C Plastic Stanchion Base is also listed here under C&C Yachts Stanchion Bases. For Backing Plates, See: Stanchion Base Backing Plates. CS Yachts Aluminum Stanchion Bases |
| C&C Stanchion Bases C&C Yachts produced a variety of proprietary Cast Aluminum (& Plastic) Stanchion Bases for their own boats, many are still available. C&C Yachts also used some SS Stanchion Bases, See Stainless Steel Stanchion Bases. +2EF |
|
| Special Stanchion Base for C&C Redline 25: SB 36-125CC: Special for C&C Yachts. Square Base with curved bottom has Stanchion at 45° angle. Base measures 3 1/2" x 3 3/8" and attaches to Deck with (4) 1/4" FH screws. Cast aluminum Base is clear anodized. As used on some C&C Redline 25.
|
|
| Toerail Mounted Stanchion Base for C&C: SB 36-220CC: Special for C&C Yachts. Stanchion Base fits over Toerail and attaches to Deck (through Toerail) with (2) 1/4" FH screws on 2 5/8" centers, a third screw (1/4" FH) goes through Stanchion and Toerail, bottom is flat. Cast aluminum Base is (maximum) 3 7/8" long x 2 1/2" wide with black epoxy finish. As used on some C&C 40's, Nautilus 40's, and others. bfla
|
 |
| Toerail Mounted Stanchion Base for C&C: SB 36-203CC: Special for C&C Yachts. Stanchion Base fits over Toerail and attaches to Deck (through Toerail) with (2) 1/4" FH screws on 2 3/8" centers, a third screw (1/4" FH) goes through Stanchion and Toerail. Small lip on outboard side touches deck. Cast aluminum Base is (maximum) 3 1/2" long x 2 5/8" wide with black epoxy finish. This unit replaced the earlier CC 36-204C, below, in C&C production, eliminating an additional Deck hole. As used on some C&C 32's, 41's, later Grampians, and others. c
|
 |
| Toerail Mounted Stanchion Base for C&C: SB 36-204CC: Special for C&C Yachts. Stanchion Base fits over Toerail and attaches to Deck with (3) 1/4" FH screws, 2 of which go through Toerail. Screws (through Toerail) are on 2 3/8" centers. Stanchion is attached with a 1/4" RH screw goes through Toerail and Stanchion, hole in Stanchion is normally tapped for 1/4" screw. Cast aluminum Base is (maximum) 3 1/2" long x 3 5/8" wide with black epoxy finish. This unit was replaced in C&C production by the redesigned CC 36-203C, above, eliminating an additional Deck hole. As used on C&C 30, 34, 36, and others. -'81a
|
|
| Toerail Mounted Stanchion Base for C&C: SB 36-255CC: Special for C&C Yachts. Stanchion Base fits over Toerail and attaches to Deck with (4) 1/4" RH screws, 2 of which go through Toerail. Screws are on 2 3/4" (outboard) and 1 9/16" (inboard) centers. Stanchion is attached with a 1/4" RH screw goes through Toerail and Stanchion, hole in Stanchion is normally tapped for 1/4" screw. Cast aluminum Base is (maximum) 3 5/8" long x 3 3/8" wide with black anodized finish. d
|
|
| Toerail Mounted Stanchion Base for C&C: SB 36-255CCP: Special Plastic Stanchion Base for C&C Yachts. Stanchion Base fits over Toerail and attaches to Deck with (4) 1/4" RH screws, 2 of which go through Toerail. Screws are on 2 3/4" (outboard) and 1 3/8" (inboard) centers. Stanchion is attached with a 1/4" RH screw goes through Toerail and Stanchion, hole in Stanchion is normally tapped for 1/4" screw. Molded Black Plastic Base is (maximum) 3 5/8" long x 3 3/8" wide. As used on C&C 37R, and others.
|
 |
|
CS Yachts Stanchion Bases CS Yachts produced a variety of proprietary Cast Aluminum Stanchion Bases for their own boats, most are still available. |
|
| Special Stanchion Base for CS 27: SB 36-027CS: Special Stanchion Base as used on early CS 27's. Base sits flat on Deck and attaches to Deck with (2) 1/4" FH screws, unusual style incorporates a vertical male stud, that stanchion fits over. Cast aluminum Base is (maximum) 5" long x 2 3/4" wide with black anodized finish.
|
|
| Special Stanchion Base for CS Yachts: SB 36-030CS: Special for CS 27, 30, and 33. Base sits on Toerail and attaches to Deck with (3) 1/4" FH screws, 2 of which go through Toerail. Cast aluminum Base is (maximum) 5" long x 2 3/4" wide with clear anodized finish. Compatible with CS 747-1 (Size 1) Toerail.
|
|
| Special Stanchion Base for CS Yachts: SB 36-034CS: Special for CS 34, 36, and 40. Base sits on Toerail and attaches to Deck with (3) 5/16" FH screws, 2 of which go through Toerail. Cast aluminum Base is (maximum) 5" long x 3" wide with clear anodized finish. Compatible with CS 747-2, and CS 747-3 (Size 2 and 3) Toerails.
|
|
| Goiot Stanchion Bases | |
| Goiot Deck Mounted Stanchion Base: Goi 800-8: Triangular-shaped Stanchion Base attaches to Deck with (3) 6mm (1/4") FH screws. Cast aluminum Base has 6mm tapped hole for screw to secure stanchion, and 27mm hole for Stanchion. Includes plastic stanchion sleeve, making it suitable for use with 25mm and 1" stanchions. Base has 6mm hole for attachment of furling blocks and sits 4mm off of deck, to improve drainage. ###
|
 |
| Goiot Toerail Mounted Stanchion Base: Goi 808-8: Toerail-mounted Stanchion Base adds additional support to Stanchion. Extruded aluminum Stanchion Base has lug that locks into Toerail lip and attaches to deck with (2) 6mm (1/4") FH screws. Base has 6mm Clevis Pin (included) to secure stanchion, and 25mm hole for Stanchion. For use with 25mm stanchions and Goiot 808 Toerail.
|
 |
| Goiot Toerail Mounted Stanchion Base: Goi 810-8: Toerail-mounted Stanchion Base adds additional support to Stanchion. Triangular-shaped Stanchion Base has lug that locks into Toerail slot and attaches to deck with (2) 6mm (1/4") FH screws on 55mm (2 1/8") centers. Cast aluminum Base has 6mm tapped hole for screw to secure stanchion, and 27mm hole for Stanchion. Includes plastic stanchion sleeve, making it suitable for use with 25mm and 1" stanchions. Unit is (maximum) 3" (77mm) high x 3 3/16" (80mm) wide. For use with Goiot 811 Toerail. 811-27
|
 |
| Goiot Toerail Mounted Stanchion Base: Goi 820-8: Toerail-mounted Stanchion Base adds additional support to Stanchion. Rectangular Stanchion Base has threaded holes for attachment to Toerail side with (2) 6mm screws on 60mm (2 5/16") centers, and through Toerail with (1) 6mm (1/4") screw (under Stanchion). Cast aluminum Base has 6mm tapped hole for screw to secure stanchion, and 27mm hole for Stanchion. Includes plastic stanchion sleeve, making it suitable for use with 25mm and 1" stanchions. Unit is (maximum) 2 7/8" (73mm) high x 3" (77mm) wide. For use with Goiot 822 and 823 Toerail. 822-27
|
 |
| Miscellaneous Aluminum Stanchion Bases | |
| Toerail Mounted Stanchion Base: GS 36-1TC: Toerail-mounted Stanchion Base adds additional support to Stanchion. Rectangular Stanchion Base has lug that locks into Toerail slot and attaches to deck with (2) 6mm (1/4") FH screws on 55mm (2 3/16") centers. Cast aluminum Base is 3 1/4" long x 2 1/2" wide (excluding lug) with black anodized finish, and has 6mm tapped hole for screw to secure stanchion. As used on Gibsea, Kirie Elite, and others. ### TTR
|
|
| Toerail Mounted Stanchion Base w/ Deck Lip: BE 36-AT600B: Toerail-mounted Stanchion Base attaches to deck with (2) 6mm (1/4") FH screws on 2" (50mm) centers and has 5mm threaded hole for screw which attaches it to Toerail. Base has separate 8mm threaded hole for screw to secure Stanchion. Cast aluminum Base is 2 3/4" (70mm) long (outboard) x 2" long (at Toerail) x 2 3/4" (70mm) wide with Black anodized finish. As used on Beneteau and others. 334600
|
|
| Toerail Mounted Stanchion Base w/ Deck Lip: BE 36-AT314: Toerail-mounted Rectangular Stanchion Base attaches to deck with (2) 6mm (1/4") FH screws on 2 3/16" (55mm) centers, and has 8mm threaded hole for screw which attaches it to Toerail and secures Stanchion. Cast aluminum Base is 3 3/8" (85mm) long x 2 1/4" (57mm) wide with clear anodized finish. As used on Beneteau and others. 001314/334620B
|
|
| Toerail Mounted Stanchion Base: BE 36-AT620: Toerail-mounted Rectangular Stanchion Base bolts through Toerail and Deck with (2) 6mm (1/4") FH screws on 2 3/4" (70mm) centers, and has 8mm threaded hole for screw which attaches it to Toerail and secures Stanchion. Cast aluminum Base is 3 1/2" (90mm) long x 1 7/8" (47mm) wide x 2 3/4" (70mm) high with clear anodized finish. As used on Beneteau and others. 334550/560
|
|
| Toerail Mount Stanchion Base w/ Tapered Socket: BE 36-AT620-T: | |
| Toerail-mounted Stanchion Base as BE 36-AT620,
above, but with Tapered Socket for special Stanchion with Tapered bottom.
Commonly used with Stanchion Gate Brace assemblies. 650
|
|
| Mini Toerail Mount Stanchion Base: BE 36-AT877M: Toerail-mounted Triangular Stanchion Base bolts through Toerail and Deck with (1) 8mm (5/16") screw (under Stanchion), and has 8mm threaded hole for screw which attaches it to Toerail and secures Stanchion. "Mini" Cast aluminum Base is (maximum) 2 1/8" (54mm) long (fore & aft) x 1 7/8" (48mm) wide x 2 3/4" high with clear anodized finish. As used on Beneteau and others. 002877
|
|
| Mini Toerail Mount Stanchion Base w/ Tapered Socket: BE 36-AT877M-T: | |
| Toerail-mounted Stanchion Base as BE 36-AT877M, above, but with Tapered Socket for special Stanchion with Tapered bottom. Commonly used with Stanchion Gate Brace assemblies. 878 | |
~ Back to Stanchion Bases Main Page ~